To Next PageTo Next Page
Need help?Do you have a question about the evertz 7700 Series and is the answer not in the manual?
Input and output BNC connectors for serial digital video signals compatible with SMPTE 292M or 259M-C.
Input BNC for analog Genlock reference (tri-level, NTSC, PAL) and termination settings.
Four unbalanced AES inputs/outputs for SMPTE 276M signals on the EAES4 version.
2x3 terminal block for two GPI inputs and two GPO outputs on the FSE-GPI version.
Input specs: standard, connector, equalization, and return loss.
Output specs: number of outputs, connectors, signal level, and jitter.
Genlock input type, connector, and termination details.
AES audio input/output specs: number, standard, resolution, sampling rate.
Specifications for general purpose interface inputs and outputs.
Configuration parameters for video and audio processing.
Details on video and audio processing delay.
Specifications for the RS 232 serial port for data logging.
Electrical specs: voltage and power consumption.
Physical specs: frame mounting and number of slots.
Details on Module OK, Local Fault, Video Present, Audio Present LEDs.
Description of the four small LEDs indicating audio channels present.
LEDs indicating audio levels and sub-board status (EAES4-HD version).
Status of audio sub-board: Green (Correct), Off (Not Configured), Red (Error).
Configure module for remote control via SNMP using VistaLINK®.
Use DIP switch 2 for horizontal/vertical display orientation.
Use DIP switches 5-8 to select the video format.
Use toggle switch and pushbutton to navigate the menu.
Description of the top-level menu tree for parameter adjustment.
Display module status and DIP switch settings via serial port.
Configure video parameters: phase, delay, freeze mode.
Parameters for video processing: black level, luminance, chroma, hue.
Frame lock parameters for SD video: mode and V-bit transition.
AFD parameters: mode, embed line, control code, aspect ratio, bar size.
Audio parameters: sample rate converter, breakout mode, de-embedding, embedding.
Audio processing: re-mapping channels and setting audio levels.
Configure thumbnail capture and sending over Ethernet.
Controls to selectively blank lines 6-29 in both fields.
Logged messages and descriptions for normal operation.
Specific logged messages applicable only to the EAES4 version.
Determine if local faults connect to the frame's global status bus.
Procedure for firmware upgrades using J16 jumper.
Use TERM/UNTERM jumper for genlock input termination.
Terminate DARS input using J5 jumper (EAES4-HD only).
Procedure to restore factory defaults using serial upgrade cable.
Configure video sync with uncompressed embedded audio.
Configure video sync with separate AES audio inputs.
Delay video and embed compressed audio from AES.
Sync video/compressed audio, output to decompressor, re-embed uncompressed.
Delay video/uncompressed audio, output to compressor, embed compressed.
Sync video, de-embed audio to AES outputs, embed new AES audio.
Overview of VistaLINK® remote monitoring and configuration platform.
List of parameters remotely monitored via VistaLINK® interface.
List of parameters remotely controlled via VistaLINK® interface.
Traps triggering alerts for specific events in VistaLINK®.
Configuration instructions for IntelliGain®.
Input and output BNC connectors for serial digital video signals compatible with SMPTE 292M or 259M-C.
Input BNC for analog Genlock reference (tri-level, NTSC, PAL) and termination settings.
Four unbalanced AES inputs/outputs for SMPTE 276M signals on the EAES4 version.
2x3 terminal block for two GPI inputs and two GPO outputs on the FSE-GPI version.
Input specs: standard, connector, equalization, and return loss.
Output specs: number of outputs, connectors, signal level, and jitter.
Genlock input type, connector, and termination details.
AES audio input/output specs: number, standard, resolution, sampling rate.
Specifications for general purpose interface inputs and outputs.
Configuration parameters for video and audio processing.
Details on video and audio processing delay.
Specifications for the RS 232 serial port for data logging.
Electrical specs: voltage and power consumption.
Physical specs: frame mounting and number of slots.
Details on Module OK, Local Fault, Video Present, Audio Present LEDs.
Description of the four small LEDs indicating audio channels present.
LEDs indicating audio levels and sub-board status (EAES4-HD version).
Status of audio sub-board: Green (Correct), Off (Not Configured), Red (Error).
Configure module for remote control via SNMP using VistaLINK®.
Use DIP switch 2 for horizontal/vertical display orientation.
Use DIP switches 5-8 to select the video format.
Use toggle switch and pushbutton to navigate the menu.
Description of the top-level menu tree for parameter adjustment.
Display module status and DIP switch settings via serial port.
Configure video parameters: phase, delay, freeze mode.
Parameters for video processing: black level, luminance, chroma, hue.
Frame lock parameters for SD video: mode and V-bit transition.
AFD parameters: mode, embed line, control code, aspect ratio, bar size.
Audio parameters: sample rate converter, breakout mode, de-embedding, embedding.
Audio processing: re-mapping channels and setting audio levels.
Configure thumbnail capture and sending over Ethernet.
Controls to selectively blank lines 6-29 in both fields.
Logged messages and descriptions for normal operation.
Specific logged messages applicable only to the EAES4 version.
Determine if local faults connect to the frame's global status bus.
Procedure for firmware upgrades using J16 jumper.
Use TERM/UNTERM jumper for genlock input termination.
Terminate DARS input using J5 jumper (EAES4-HD only).
Procedure to restore factory defaults using serial upgrade cable.
Configure video sync with uncompressed embedded audio.
Configure video sync with separate AES audio inputs.
Delay video and embed compressed audio from AES.
Sync video/compressed audio, output to decompressor, re-embed uncompressed.
Delay video/uncompressed audio, output to compressor, embed compressed.
Sync video, de-embed audio to AES outputs, embed new AES audio.
Overview of VistaLINK® remote monitoring and configuration platform.
List of parameters remotely monitored via VistaLINK® interface.
List of parameters remotely controlled via VistaLINK® interface.
Traps triggering alerts for specific events in VistaLINK®.
Configuration instructions for IntelliGain®.
General| Category | Computer Hardware |
|---|---|
| Model | 7700 Series |
| Format | Modular |
| Control | Software-based |
| Control Interface | Ethernet |
| Power Supply | Redundant |
| Weight | Varies depending on module and frame size. |
| Input Formats | SDI |
| Output Formats | SDI |
| Audio Standards | AES3 |
