Why does my Exmark Lazer Z Air-cooled pull left or right?
If your Exmark Lawn Mower is pulling to the left or right, it might be due to incorrect tire pressure in the drive tires. Adjust the tire pressure to correct this.
Why my Exmark Lawn Mower engine will not start?
If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, first ensure the fuel tank isn't empty and the fuel shutoff valve is open. Check the oil level in the crankcase and add oil if needed. Make sure the throttle and choke are in the correct positions. Replace the fuel filter if it's dirty, and inspect/clean or replace the air filter. Inspect the spark plug wire connection and clean, adjust, or replace the spark plug. Also, check the seat switch indicator and replace the seat if needed. Inspect the electrical connections for good contact, cleaning them as necessary. For issues related to stale fuel, or defective relay, switch, or module, consider contacting an authorized service dealer.
What to do if my Exmark Lazer Z Air-cooled Lawn Mower engine will not start?
If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, consider the following: * The fuel tank might be empty, so fill it up. * The fuel shutoff valve could be closed, so open it. * The oil level in the crankcase might be low, so add oil. * The throttle and choke may not be correctly positioned; ensure the throttle is midway between “SLOW” and “FAST,” and the choke is “ON” for a cold engine or “OFF” for a warm engine. * A dirty fuel filter can cause starting issues, so replace it. * A dirty air cleaner can prevent the engine from starting; clean or replace the air cleaner element. * Check the seat switch indicator. Replace seat if needed. * Also, check the spark plug wire connection and clean, adjust, or replace the spark plug if faulty.
Why won't my Exmark Lazer Z Air-cooled engine start?
If your Exmark Lawn Mower engine won't start, several factors could be the cause. Here are some things to check: * Ensure the battery is fully charged. * Position the throttle control midway between “SLOW” and “FAST,” and set the choke to “ON” for a cold engine or “OFF” for a warm one. * Confirm there's fuel in the tank and the fuel valve is open. * Verify the seat switch is properly adjusted. * Make sure the parking brake is set and motion control levers are in the neutral lock position. * Confirm the PTO is disengaged. * Check that the spark plug wires are properly connected. * Inspect for loose or faulty wiring connections and corrosion at all wiring connections. Clean any corrosion with electrical contact cleaner, apply dielectric grease, and reconnect.
Why won't my Exmark Lazer Z Air-cooled starter crank?
The starter may not crank for several reasons: * The PTO might be engaged: Disengage the PTO. * The parking brake might not be engaged: Set the parking brake. * The drive levers might not be in the neutral lock position: Ensure the drive levers are in the neutral lock position. * The battery might not have a full charge: Charge the battery. * Electrical connections might be corroded, loose, or faulty: Check the electrical connections for good contact, clean connector terminals, apply dielectric grease, and reconnect. * A fuse might be blown: Replace the blown fuse. * Relay or switch is defective: Contact an Authorized Service Dealer. * Faulty module: Replace module.
What causes abnormal vibration in my Exmark Lazer Z Air-cooled?
If your Exmark Lawn Mower exhibits abnormal vibration, here's what you can check: * Bent or unbalanced cutting blades can cause vibration, so install new cutting blades. * A loose blade mounting bolt can also be the culprit, so tighten it. * Check the engine mounting bolts and tighten them if they are loose. * Also, make sure the engine pulley, idler pulley, or blade pulley are not loose and tighten if necessary. * Install new belt.
What to do if my Exmark Lazer Z Air-cooled does not drive?
If your Exmark Lawn Mower doesn't drive, ensure the drive release handle is in the operating position. Change the drive or pump belt if it is worn, loose, or broken, or if it is off a pulley. Replace the idler spring if it's broken or missing. Add hydraulic fluid to the reservoir or allow it to cool down if the hydraulic fluid level is low or too hot.
Why won't the clutch engage on my Exmark Lawn Mower?
If the clutch on your Exmark Lawn Mower will not engage, replace the fuse. Check coil resistance, battery charge, charging system, and wiring connections, replacing if necessary, if there's low voltage supply at the clutch. Replace the clutch if the coil is damaged. Repair or replace the clutch lead wire or electrical system and clean connector contacts if there's inadequate current supply. Remove a shim or replace the clutch if the rotor/armature airgap is too large.
What does it mean if the oil pressure light is on and the engine RPM is low on my Exmark Lawn Mower?
If the oil pressure light is on and the engine RPM is low on your Exmark Lawn Mower, it means that the Engine Control Unit has limited engine RPMs, known as “limp” mode. Let engine cool and check oil level. If level is above 'add', contact an Authorized Service Dealer.
What to do if my Exmark Lawn Mower pulls to the left or right?
If your Exmark Lawn Mower pulls to the left or right with the levers fully forward, you should: * Check the air pressure in the tires, ensuring 13 psi for drive tires and 13 psi for pneumatic casters. * Check the reverse indicator and motion control linkage adjustment.
General| Transmission Type | Hydrostatic |
|---|---|
| Turning Radius | Zero-turn |
| Engine Type | Air-cooled |
| Speed Range | 0-10 mph |
| Wheel Options | Pneumatic |
| Weight | Varies by model, approximately 1100-1500 lbs (499-680 kg) |
To Next Page
