Exmark Lazer Z XP - User Manual

Questions and Answers

D
Daniel RossAug 15, 2025
What to do if my Exmark Lazer Z XP Lawn Mower engine will not start?
- L
  Lynn JohnsonAug 15, 2025
  If your Exmark Lawn Mower engine isn't starting, ensure the battery is fully charged. Make sure the throttle control is midway between the “SLOW” and “FAST” positions, and the choke is in the “ON” position for a cold engine or the “OFF” position for a warm engine. Also, verify there's fuel in the tank and the fuel valve is open. The operator must be in the seat, the parking brake should be set, and motion control levers moved out to the neutral lock position. Check that the blades are disengaged. For 31 HP Daihatsu Gas units, check that the spark plug wires are properly connected. Inspect for loose or faulty wiring connections and corrosion at all wiring connections; clean connector terminals with electrical contact cleaner, apply dielectric grease, and reconnect.
A
alan93Aug 18, 2025
How to fix uneven cuts with my Exmark Lazer Z XP?
- M
  Mathew SteeleAug 18, 2025
  To address uneven cuts with your Exmark Lawn Mower, start by checking the air pressure in the tires, ensuring it's at 13 psi for both the drive tires and pneumatic casters. Next, inspect the deck support chains and check the blades tip to tip for straightness, ensuring they are within 3/16" or one blade width from being in line.
S
Stephanie JosephAug 21, 2025
Why is my Exmark Lawn Mower overheating?
- H
  hcollinsAug 21, 2025
  If your Exmark Lawn Mower overheats: * Disengage the mower blades and idle down the engine. * Check the temperature gauge; if the temperature continues to rise, turn off the unit and let it cool. * Check the coolant level and add coolant if needed. * Remove any debris around the radiator that may restrict airflow. * Check if the water pump/alternator belt is intact. If the belt is missing, do not run the unit.
C
charles81Aug 25, 2025
How to fix an Exmark Lazer Z XP Lawn Mower that cuts unevenly?
- K
  Kenneth GriffithAug 26, 2025
  To address uneven cuts with your Exmark Lawn Mower, start by checking the air pressure in the drive tires, ensuring they are at 10 psi. Inspect the deck support chains and verify the deck leveling. Also, check the blades for straightness, ensuring they are within 3/16" or one blade width from being in line.
D
Dominique CookAug 28, 2025
Why does my Exmark Lazer Z XP cut unevenly?
- J
  Justin BartlettAug 28, 2025
  If your Exmark Lawn Mower cuts unevenly, begin by checking the air pressure in the tires, ensuring they are at 13 psi for both the drive tires and pneumatic casters. For rough terrain, a more uniform cutting height may be achieved with higher tire pressure. Inspect the deck support chains and verify the deck leveling. Lastly, check the straightness of the blades from tip to tip, ensuring they are within 3/16" or one blade width from being in line.
B
bmcleanAug 31, 2025
How to fix Exmark Lawn Mower that pulls left or right?
- U
  uwilliamsSep 1, 2025
  If your Exmark Lawn Mower pulls to the left or right with the levers fully forward, move the levers forward and compensate as necessary. Check the air pressure in the tires, ensuring it's at 13 psi for both the drive tires and pneumatic casters. Also, inspect the reverse indicator and motion control linkage adjustment.
K
Katherine BlairSep 4, 2025
Why does my Exmark Lazer Z XP Lawn Mower pull to the left or right?
- T
  Tony MarshallSep 4, 2025
  If your Exmark Lawn Mower pulls to the left or right with the levers fully forward, move levers forward and compensate as necessary. Check the air pressure in the tires, ensuring they are at 13 psi for the drive tires and 13 psi for the pneumatic castors. Inspect the reverse indicator and motion control linkage adjustment.
I
imillerSep 7, 2025
How to stop my Exmark Lazer Z XP Lawn Mower from pulling to one side?
- D
  Dennis BrownSep 7, 2025
  To correct an Exmark Lawn Mower that pulls to the left or right, check the air pressure in the drive tires and ensure they are at 10 psi. Also, inspect the reverse indicator and motion control linkage adjustment.
J
John ThompsonSep 10, 2025
What to do if the 'Water in Fuel' light is on in my Exmark Lazer Z XP?
- C
  Chad GarzaSep 12, 2025
  If the Water in Fuel light is on for your Exmark Lawn Mower, drain water from the fuel filter.

Summary

SAFETY

Safety Alert Symbol and Operator Training

Explains safety symbols, operator training requirements, and preparation.

Operational Safety and Slope Hazards

Covers safe operation, hot parts, rotating parts, and slope safety.

OPERATION GUIDELINES

Starting, Mowing, PTO, Stopping, and Transport Procedures

Covers pre-start, starting, mowing, PTO use, stopping, and transport.

MAINTENANCE AND ADJUSTMENTS

Daily Checks, Safety, and Component Service

Daily checks, safety precautions, and servicing blades, air cleaners, filters.

WASTE DISPOSAL

TROUBLESHOOTING AND WARNING SYSTEMS

Common Mower Problems and Diagnosis

Addresses issues like pulling, cutting, and starting problems.

Engine Warning Systems and Indicators

Explains warning lights and buzzers for engine status.

ELECTRICAL DIAGRAM

System Wiring Schematic

HYDRAULIC DIAGRAM

System Components and Flow Chart

LIMITED WARRANTY INFORMATION

Exmark Lazer Z XP Specifications

General

Blade Tip Speed	up to 18, 500 FPM
Spindle Material	Aluminum
Drive Type	Hydrostatic
Reverse Speed	up to 5 mph
Engine Type	Gasoline
Engine Manufacturer	Kawasaki or Kohler
Deck Type	Welded Steel
Tires (Front)	13 x 6.5 - 6
Tires (Rear)	24x12.00-12 or 26x12.00-12
Turning Radius	Zero-turn