A
Anne MercadoAug 15, 2025
What to do if the Exmark Lawn Mower fuel is low?
- EeclarkAug 15, 2025
If the fuel level is low on your Exmark Lawn Mower, check the fuel level and refuel as necessary.
To Next PageTo Next PageWhat to do if the Exmark Lawn Mower fuel is low?
If the fuel level is low on your Exmark Lawn Mower, check the fuel level and refuel as necessary.
What to do if Exmark Lawn Mower has low oil pressure?
If your Exmark Lawn Mower is showing a 'Low Oil Pressure' warning, it could be due to the engine oil pressure being below the limit or the engine temperature being high. Here's what you should do: * Cycle the key switch to clear the fault and check the oil level. * If the engine temperature is high, clean any debris from the engine and inspect the engine fan. * If the issue persists, contact an Authorized Service Dealer.
What to do if Exmark LZS850EKA724W0 Lawn Mower engine over temperature?
If your Exmark Lawn Mower engine is overheating, it means the engine temperature is above the limit. You should check the oil level, clean any debris from the engine, and inspect the engine fan. If the problem continues, contact an Authorized Service Dealer.
What to do if Exmark LZS850EKA724W0 Lawn Mower system voltage is low?
If the system voltage is low (below 12.3 volts) on your Exmark Lawn Mower, check the battery and engine charging system. If problems persist, contact an Authorized Service Dealer.
What to do if Exmark LZS850EKA724W0 Lawn Mower system overvoltage is greater than 16VDC?
If your Exmark Lawn Mower displays a 'System Overvoltage' error (above 16 volts), it indicates excessive system voltage. Check the battery and engine charging system. For further assistance, contact an Authorized Service Dealer.
What to do if Exmark Lawn Mower system undervoltage is less than 9VDC?
If your Exmark Lawn Mower displays a 'System Undervoltage' error (below 9 volts), it indicates that the system voltage is below the lower limit. You should check the battery and engine charging system. For further assistance, contact an Authorized Service Dealer.
What to do if Exmark LZS850EKA724W0 Lawn Mower clutch overcurrent?
If your Exmark Lawn Mower is showing a 'Clutch Overcurrent' error, it means that the clutch current is above the limit. Cycle the key switch to clear the fault. Check the PTO clutch condition and related wiring. If the problem persists, contact an Authorized Service Dealer.
What to do if Exmark LZS850EKA724W0 clutch output fault?
If your Exmark Lawn Mower is showing a 'Clutch Output Fault', it means that the clutch output is shorted or open. If the clutch is stuck 'ON', stop using the mower and contact an Authorized Service Dealer. Check the clutch connection and associated wiring for an open circuit.
How to reset clutch on Exmark LZS850EKA724W0 Lawn Mower?
If your Exmark Lawn Mower indicates that a clutch reset is required, cycle the PTO switch OFF and then back ON to re-engage the clutch.
General| Category | Lawn Mower |
|---|---|
| Engine | Kawasaki |
| Displacement | 850cc |
| Cutting Width | 72 in |
| Deck Type | Fabricated |
| Blade Tip Speed | 18, 500 fpm |
| Drive Type | Hydrostatic |
| Turning Radius | Zero-Turn |
| Type | Zero Turn |
| Speed Reverse | 5 mph |
| Speed Range | 0-5 mph reverse |
Displays icons and information relative to machine operation.
Multi-colored LED indicates system status and verifies functionality.
Multi-functional buttons for navigation and control.
Sounds to indicate errors and verify functionality during startup.
Displays during module startup, shows RED Equipped logo.
Default screen when key is on, engine is off.
Default screen when engine is running, shows operational data.
Screen accessed via specific button combination for menu navigation.
Access to maintenance and service-related information and logs.
View various operating parameters and counters.
Access to configuration and advanced system settings.
Lists system inputs and highlights active ones.
Lists system outputs and highlights active ones.
Displays active error messages with occurrence details.
Service reminder for hydraulic transmission oil.
Service reminder for engine oil.
Displays serial number and model number of the machine.
Shows installed software and hardware versions for LDU/MCU.
Displays total and resettable engine hour counters.
Displays total and resettable PTO hour counters.
Displays total fuel consumed since last reset.
Displays fuel consumption per engine hour.
View and manage trip statistics and parameters.
Resets the engine oil service reminder.
Resets the transmission oil service reminder.
View past error messages and their occurrence count.
Controls audible alarms for specific errors.
Adjusts engine speed for various operating modes.
Calibrates actual engine speed to commanded speed.
Resets system settings to factory defaults.
