F'real FRLB4 - Non-Error Troubleshooting; Registration and Touchscreen Issues; Front Door and Water Leak Issues

20
Non-Error Issues
“Registraon Required”
TRIGGER: Blender has failed to check-in with our servers for a period of greater than 7 days
1. Contact the f’real Customer Support Center to retrieve the PIN Number.
2. Be prepared with the following items:
A. Blender Serial Number (SN)
B. Locaon’s name and store number (if applicable)
C. Locaon's full address and phone number
3. Ensure the blender is checking in with our servers.
Touchscreen Issues
TRIGGER: The touchscreen’s calibraon is o or not responding at all
1. Press the “Regular” and “OK” buons together for 7 seconds to bring up the Calibraon screen.
2. Follow the on-screen instrucons to calibrate the touchscreen.
3. Press the “Less Thick” and “OK” buons together for 7 seconds. A number pad will appear on the screen. To test the
calibraon, aempt to put in the numbers, “411.”
A. If you are successful, press the “Back” buon unl videos are playing.
B. If you are unsuccessful, touch the screen to locate a ny black dot (cursor). Choose from one of the opons below that t
the status of your screen:
a. You are unable to locate a dot, call the f’real Customer Support Center to verify which Single Board Computer your
blender has and the locaon of the wiring connecons.
b. If you are able to nd the dot and it is consistently the same distance away from your nger, no maer where you
touch the screen, aempt to calibrate again aer you’ve wiped the screen clean and washed your hands. If the is-
sue remains, replace Single Board Computer (Parts Manual: Control Boards, Lower).
c. If you are able to locate the dot, but the dot is always a dierent distance away from your nger, no maer where
you touch the screen, replace Front Door with Screen Assembly (Parts Manual: LCD Panel).
Front Door Issues
TRIGGER: Issues with a door that will not stay shut or a door that will not open
Door will not stay shut:
1. Aempt to close the door by rmly pressing the lower right side of the LCD touchscreen bezel unl you hear the latch ‘click’.
Cauon: Do not slam the door. Slamming the door will damage the LCD touchscreen.
2. If the door sll won’t close, slowly close the front door and watch where the front door latch meets the blender frame. If the
latch has been bent then it may not meet up with the blender frame like it should. The latch may need to be bent slightly to
meet the frame more accurately.
3. If the assembly is lined up correctly and sll not shung/latching, the front door latch may need to be "shimmed" out. Remove
the 9/64" Allen head screws holding the latch on the door and place one washer behind each screw and re-assemble.
4. If door sll won’t shut, replace Door Latch Assembly (Parts Manual: Door Latch & Lock System).
Door will not open:
1. Remove the right side panel and locate the Door Latch Tab. Place a Flat-Head Screwdriver on the boom of the tab and press
vercally unl the door pops open.
A. If it opens, slowly close the front door and watch where the front door latch meets the blender frame. If the latch has
been bent then it won’t meet up with the blender frame. The latch may need to be bent slightly to meet the frame.
B. If it will not open, the Flip-Up Door Lock may be energized. If the latch releases when the front door lock wiring is
unplugged, then check for shorts and re-seat the Front Door Wiring. If no shorts or issues, replace Low Voltage Control
Board (LVCB) (Parts Manual: Control Boards, Lower).
2. If above Troubleshoong does not resolve the issue, replace Door Latch Assembly (Parts Manual: Door Latch & Lock System).
Front Door Water Leaks
TRIGGER: During any water event, water will leak from in between the front door and the chamber onto the keypad below.
NOTICE: If your front door gasket surrounds the chamber, you may disregard the following troubleshoong steps.
1. Ensure the door is completely closed and not parally closed.
2. Open the front door and locate the Front Door Gasket on the back side of the door.
A. Remove the Front Door Gasket from the channel it's inserted into on the Front Door Wedge.
a. There are two sides to the gasket. The front of the Gasket has a raised secon and two small ribs on the outside
edge. The back of the gasket has two secons with a seam down the middle.