What to do if the water doesn't drain from my Fagor Dishwasher?
If water remains in your Fagor Dishwasher after a cycle, check if the drain is blocked or poorly fitted. Also, inspect the drainage pipe for blockages or kinks. Ensure the filters are not blocked. If the program hasn't ended, wait until it finishes.
How to fix a Fagor 2LF 013 IX that won't start?
If your Fagor Dishwasher won’t start, possible solutions include ensuring it is properly connected to a power source, such as being correctly plugged in or connected to the mains. Check that the power fuses have not blown. Make sure you have pressed the On/Off button and that the pilot light is lit. Also, verify that the dishwasher door is completely closed and that you have pressed the Start button.
Why are there remains of dirt or food on the utensils after using my Fagor Dishwasher?
If you find dirt or food remains on utensils after a Fagor Dishwasher cycle, consider these points: * Check if the wash filter is dirty, blocked, or incorrectly placed. * Inspect the sprinkler nozzles for blockages or obstructions caused by utensils. * Ensure you're using an adequate amount of appropriate detergent. * Position utensils correctly to avoid contact with each other, and don't overload the racks. * Select the appropriate wash program. * Check for a blocked drain. * Note that old, dry food remains may be difficult to remove.
What to do if my Fagor Dishwasher starts but no water comes in?
If your Fagor Dishwasher starts but no water enters the appliance, make sure that there is a water supply and that the stop tap is turned on. Additionally, check the water inlet electrovalve filter for any blockages.
Why don't the utensils come out dry from my Fagor 2LF 013 IX?
If the utensils in your Fagor Dishwasher are not drying properly, ensure that there is rinse-aid and that the rinse-aid control is correctly set. Check that the utensils are positioned correctly and are not being taken out too soon. Also, verify that the wash program you are using is appropriate.
Why do the utensils come out white after using my Fagor Dishwasher?
If utensils come out white after being washed in your Fagor Dishwasher, ensure that you are using enough detergent and rinse-aid. Check that the salt container lid is correctly closed and that the container has water and salt. Also, verify that the water softener is correctly adjusted to the water hardness level. Consider using a detergent containing phosphate if you are currently using a phosphate-free detergent.
Why does my Fagor Dishwasher use so much salt?
If your Fagor Dishwasher is using a lot of salt, verify that the lid to the salt container is closed correctly and that the salt consumption level is set correctly.
Why are there traces of detergent left in the dispenser of my Fagor 2LF 013 IX?
If you notice traces of detergent in the dispenser or on the door of your Fagor Dishwasher, check whether any utensil is obstructing the dispenser from opening. Ensure the detergent is not expired and is appropriate for dishwashers. Make sure the sprinklers are not rubbing on any dishes and that their nozzles are not blocked. Also, verify that the detergent container was dry when you added the detergent.
Why is my Fagor 2LF 013 IX making strange noises?
If your Fagor Dishwasher is making strange noises, it might not have been installed correctly, or the spray arms could be rubbing against a dish.
Why won't the low salt level light go off on my Fagor 2LF 013 IX?
If the low salt level pilot light on your Fagor Dishwasher remains on, add salt and stir with a spoon. If the water hardness is below 7DH, salt is unnecessary, and the light will stay on.
Connect water inlet and outlet pipes correctly for dishwasher operation.
Ensure proper and safe electrical connections according to the specification label.
Place the dishwasher on a level surface and position it correctly.
Instructions for fitting decor panels or doors to the dishwasher.
Select the preferred language for the dishwasher's display menus.
Guidance on managing water hardness, salt, rinse-aid, and detergent for optimal washing.
Instructions for adjusting the salt level, both manually and electronically.
How to fill the salt container and when it needs refilling.
How to adjust and refill the rinse-aid dispenser for proper drying.
How to pour detergent and considerations for using different types.
Guidance on types of dishes and how to position them in the racks for best wash results.
How to adjust the height of the dishwasher racks for different load sizes.
Steps for choosing the appropriate wash cycle based on model type.
Details of available wash programs, temperatures, symbols, and consumption.
Options to customize wash cycles like time delay, extra drying, and load selection.
How to start the dishwasher and track programme phases and completion.
What to do during power interruptions and general advice for efficient use.
Step-by-step guide to cleaning the dishwasher's internal filter system.
Instructions for cleaning spray arms, the inside, and the outside of the dishwasher.
Using error codes and beeps to diagnose and resolve technical problems.
Resolving problems like the dishwasher not starting or not filling with water.
Fixing common issues like utensil cleanliness, dryness, and appearance.
Visual guides and specific dimensions for proper dishwasher installation.
General| Door color | Not applicable |
|---|---|
| Display type | LED |
| Appliance placement | Semi built-in |
| Control panel color | Stainless steel |
| Washing class | A |
| Annual water consumption | 3640 L |
| Annual energy consumption | 283 kWh |
| Cycle time | 160 min |
| Noise level | 50 dB |
| AquaStop function | Yes |
| Number of washing programs | 5 |
| Connected load | 2170 W |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 Hz |
| Water consumption per cycle | 13 L |
| Energy consumption per cycle | 1.05 kWh |
Weight and Dimensions| Depth | 570 mm |
|---|---|
| Width | 595 mm |
| Height | 820 mm |
To Next Page
