Femi 842 - Page 14


11
(1
/HJHQG)LJ

Control handgrip
 Main switch start button
 Base
 Body/base swivel joint
 Rotating bearing
 Motor
 Blade
 Lever to unblock graduation
 Button to unblock body descent
 Permanent blade shield
 Movable blade shield
 Bar clamp shaft (optional)
 Dust exhaust manifold
 Work piece clamps (optional)
 Upper work surface
 Movable upper safety guard
 Bearing bracket
 Support feet
 Transport locking pin
 Main switch locking device
 Main switch release device
 ,167$//$7,21
 5(029$/2)3$&.$*,1*
Remove the box used to protect the machine during
transport and keep it intact for future transport and/or
storage.
 +$1'/,1*
This mitre-saw is small and light and, therefore, can be
easily handled by one person alone by locking the
transportation block by means of the pin
 and by
lifting the machine by means of the control handgrip
 .
 :$51,1* :KHQ WUDQVSRUWLQJ WKH PDFKLQH
WKHXSSHUSDUWRIWKHEODGHPXVWEHFRYHUHG

$OZD\VFKHFNWKDW WKH EODGHLVSURWHFWHGE\
WKHUHODWLYHXSSHUJXDUG
 75$163257$7,21
To transport the machine, place it in the box it was in
when purchased. Ensure it is placed in the correct
position indicated by the arrows on the packaging.
Pay careful attention to the ideograms printed on the
box as they provide all necessary information for
palletization and stacking of boxes.
Tying the load down with ropes or safety belts is
recommended during transportation to stop the load
from sliding or falling.
 326,7,21:25.67$7,21)LJ
Place the machine on a work bench or on a sufficiently
flat base/pedestal to ensure the best possible stability. -
Should you wish to fix the machine in place, use the
special holes located on the base.
Bearing in mind ergonomic criteria, the ideal height of
the bench or of the base should be such that the base
surface or the upper work surface is between 90 and 95
cm. from the ground
VHHILJ .
Always ensure that there is at least 80 cm. of
manoeuvring space in all directions around the machine
in order to perform all necessary cleaning, maintenance
and adjustment operations safely with a sufficient
amount of space available
VHHILJ .
&$87,21 (QVXUH WKH PDFKLQH LV SODFHG LQ D
VXLWDEOH SRVLWLRQ ERWK LQ WHUPV RI
HQYLURQPHQWDOFRQGLWLRQVDQGOLJKWLQJ
$OZD\VEHDULQPLQGWKDWJHQHUDOHQYLURQPHQWDO
FRQGLWLRQV DUH RI IXQGDPHQWDO LPSRUWDQFH WR
SUHYHQWDFFLGHQWV

 (/(&75,&$/&211(&7,216
Check that the electrical system to which the machine is
connected is earthed in compliance with current safety
regulations and that t
he current socket is in perfect
condition.
The electrical system must be fitted with a
magnetothermal protective device to safeguard all
conductors from short circuits and overload.
The selection of this device should be in line with the
following electric
al specifications of the machine stated
on the motor.
127( <RXU PLWUH
VDZ¶V HOHFWULFDO V\VWHP LV
HTXLSSHG ZLWK DQ XQGHU
YROWDJH UHOD\ ZKLFK
DXWRPDWLFDOO\ RSHQV WKH FLUFXLW ZKHQ WKH
YROWDJH IDOOV EHORZ D PLQLPXP SUH
HVWDEOLVKHGOLPLWDQGZKLFKSUHYHQWVWKHVHOI
UHVHW RI PDFKLQH IXQFWLRQV ZKHQ YROWDJH
UHWXUQVWRQRUPDOOHYHOV

,IWKHPDFKLQH VWRSV
LQYROXQWDULO\GRQRWEH
DODUPHG0DNHVXUHWKDWWKHUHKDVQRWEHHQD
YROWDJHIDLOXUHLQWKHHOHFWULFDOV\VWHP