Femi 842 - Page 17

14
(1

-
Remove the external flange  , remove the blade by
sliding it out from the lower part of the head and install
a new blade.
-
Ensure that the blade’s teeth are oriented in the
direction of the arrow on the blade itself.
-
Then, remount the outer flange  , tighten the screw
 firmly, using the Allen wrenches supplied.

127( 7KH PRYDEOH JXDUG  ZLOO UHWXUQ WR
WKH FRUUHFW SRVLWLRQ DXWRPDWLFDOO\ ZKHQ WKH
PDFKLQHKHDGLVORZHUHGZLWKRXWKDYLQJWR
UHSRVLWLRQWKHSDZO

 :$51,1*1HYHULQVWDOOEODGHVZKLFKDSSHDU
WR EH FUDFNHG 2QO\ LQVWDOO EODGHV ZKLFK
FRPSO\ZLWKVWDQGDUG(1

 &877,1*&$3$&,7<)LJ
T
he following tables specifies the cutting capacity at 0°
a
nd 45° which may be achieved under the normal
c
onditions of use illustrated in this manual.
9
(56,21

9
(56,21
 $&&(6625,(6
 6(/(&7,212)7+(%/$'(
7
KH PLWUHVDZ LV ILWWHG ZLWK D :,',$ EODGH 
G
LDPHWHU[KROHLQYHUVLRQGLDPHWHU[
LQYHUVLRQ
 &/$036)LJ237,21$/
 &$87,21
:KHQ FXWWLQJ EDUV RU SLHFHV RI
DOXPLQLXP RU SODVWLF XVH RI WKH FODPS LV
DGYLVDEOHWRKROGWKHSLHFHILUPO\DJDLQVWWKH
DQJXODU EHDULQJV WKXV DYRLGLQJ PRYHPHQW
GXULQJ FXWWLQJ DQG WKHUHIRUH MDPV ZKLFK
FRXOG GDPDJH ERWK WKH ZRUN SLHFH DQG WKH
EODGH

A
lways check that the clamp jaw makes perfect contact
w
ith the piece to be cut and that it effectively holds it in
position at the base.
 68&7,21 2) '867 5(6,'8(6 )LJ
237,21$/
The mitre
-saw can be connected to an aspirator or a
d
ust collection bag can be mounted by means of the
e
xhaust manifold  .
T
he aspirator pipe or the bag sleeve must be secured to
t
he manifold by means of a band.
Users are reminded to
e
mpty the bag or aspirator container and to clean the
f
ilter regularly.
T
he air output speed must be equivalent to at least
100Nm
3
/h.
For example, "dustbin" type aspirators are suitable.
 0$,17(1$1&(
 5287,1(0$,17(1$1&(
T
he regular maintenance des
cribed above and in the
paragraph below can be carried out by unskilled
personnel.
1.
Do not oil the mitre-saw;
cutting must be carried out
in dry conditions (including the cutting of aluminium
and aluminium alloys); all rotating parts are self-
lubricating.
2.
During maintenance, wear protective gear if possible
(accident-prevention goggles and gloves).
3.
Remove cuttings when necessary both from the
cutting area, work surfaces and support bases.
Use of an aspirator or brush is recommended.
 :$51,1*'RQRWXVHFRPSUHVVHGDLU

4.
Regularly check blade conditions: if difficulties
should arise during cutting, have it sharpened by
skilled personnel or replace it if necessary.