Ferroli BlueHelix HiTech RRT C Instructions For Use, Maintenance And Installation

Ferroli BlueHelix HiTech RRT C

356 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

cod. 3541V300 — Rev. 00 - 02/2021

BlueHelix HiTech RRT C

ISTRUZIONE PER L’USO L'INSTALLAZIONE E LA MANUTENZIONE

INSTRUCCIONES DE USO, INSTALACIÓN Y MANTENIMIENTO

INSTRUCğIUNI DE UTILIZARE, INSTALARE ùI ÎNTRETINERE

INSTRUKCJA OBSáUGI, INSTALACJI I KONSERWACJI

ȅǻǾīǴǼȈ ȋȇǳȈǾȈ, ǼīȀǹȉǱȈȉǹȈǾȈ Ȁǹǿ ȈȊȃȉǳȇǾȈǾȈ

INSTRUCTIONS FOR USE, INSTALLATION AND MAINTENANCE

IT

ES

RO

PL

EL

EN

Table of Contents

Other manuals for Ferroli BlueHelix HiTech RRT C

Instructions For Use62 pages

Instructions For Use, Installation & Maintenance64 pages

Questions and Answers:

I
ibarrajulieSep 12, 2025
How to fix no burner ignition on my Ferroli BlueHelix HiTech RRT C?
- B
  Brandon CurtisSep 12, 2025
  If your Ferroli Boiler is not igniting, several factors could be at play. First, ensure that gas is flowing to the boiler and that there's no air trapped in the pipes. Check the ignition/detection electrode for proper wiring, positioning, and cleanliness; replace if needed. Insufficient gas supply pressure can also be a culprit, so verify the pressure. Other potential issues include a blocked trap (check and clean it), obstructions in the air/fume ducts (clear any blockages), incorrect calibration (perform the calibration procedure), or a faulty gas valve (inspect and replace if necessary).
T
Tina MoonAug 25, 2025
What to do if Ferroli Boiler has no flame after ignition?
- J
  Joseph JohnstonAug 25, 2025
  If your Ferroli boiler fails to maintain a flame after ignition, start by checking the ionization electrode. Ensure it's correctly positioned, free of any deposits, and perform the Calibration procedure [AUTO SETUP]. Replace the electrode if necessary. Also, inspect the burner for any issues. Clear any obstructions from the flue, fume extraction ducts, air inlet, and terminals. Check the trap and clean it if necessary. Perform the Calibration procedure [AUTO SETUP]. Ensure adequate gas supply pressure.
C
Christopher LarsonAug 25, 2025
Why does my Ferroli BlueHelix HiTech RRT C overtemperature protection activate?
- D
  Dennis VelasquezAug 26, 2025
  Overtemperature protection in your Ferroli boiler may activate due to several reasons. Check the flow or return sensors for correct positioning and operation, replacing them if necessary. Ensure there is adequate water circulation in the system by checking the circulating pump. Also, vent the system to remove any air.
R
Robert PerezAug 26, 2025
What causes exchanger protection intervention in Ferroli BlueHelix HiTech RRT C?
- M
  Meghan SanchezAug 26, 2025
  Exchanger protection intervention in your Ferroli boiler can occur due to a few reasons. Check the circulating pump and heating system to ensure proper water circulation. Vent the system if there's poor circulation and an anomalous flow probe temperature increase. Inspect the exchanger and system for blockages.
S
Shannon MartinAug 27, 2025
How to troubleshoot overtemperature protection intervention in Ferroli BlueHelix HiTech RRT C?
- J
  jeffreymannAug 27, 2025
  If your Ferroli boiler's overtemperature protection is intervening, check the flow sensor for correct positioning and operation, replacing it if necessary. Make sure there is water circulation in the system by inspecting the circulating pump and heating system. Additionally, vent the system to eliminate any air.
M
Maria BlanchardSep 8, 2025
What to do for return sensor fault in Ferroli BlueHelix HiTech RRT C?
- M
  murrayashleySep 8, 2025
  If you're experiencing a return sensor fault with your Ferroli boiler, it likely indicates a damaged sensor. Check the wiring or replace the sensor.
M
Matthew JacksonSep 6, 2025
What causes parasite flame signal after valve closing in Ferroli BlueHelix HiTech RRT C?
- K
  kevin61Sep 6, 2025
  A parasite flame signal after valve closing in your Ferroli boiler may be due to an electrode, gas valve, or PCB problem. Check the correct position and condition of the electrode. Check the PCB. Check the gas valve and replace it if necessary.
C
Carlos RamseySep 7, 2025
How to troubleshoot flow sensor fault in Ferroli BlueHelix HiTech RRT C?
- C
  Cindy AllenSep 7, 2025
  If your Ferroli boiler is showing a flow sensor fault, it could be that the sensor is damaged. Check the wiring or replace the sensor.
E
Emily KramerSep 1, 2025
What to do if overtemperature protection intervenes in Ferroli BlueHelix HiTech RRT C?
- T
  tdavidsonSep 1, 2025
  If the overtemperature protection is activated in your Ferroli boiler, it could be due to several reasons. First, check that the heating sensor is correctly positioned on the flow pipe and operating properly; replace it if necessary. Also, ensure there is proper water circulation in the system by checking the circulating pump. Finally, vent the system to eliminate any air that may be trapped inside.
A
Amber WhiteAug 30, 2025
How to resolve fume probe fault in Ferroli BlueHelix HiTech RRT C?
- A
  Ashley ButlerAug 30, 2025
  To address a fume probe fault in your Ferroli boiler, check the wiring or replace the fume probe if it's damaged.

Ferroli BlueHelix HiTech RRT C Specifications

General

Type	Condensing
Fuel Type	Natural Gas / LPG
Weight	32 kg
Efficiency Class	A
Mounting	Wall-mounted
Modulation	1:10
Heat Exchanger Material	Stainless Steel
Control	Digital
Warranty	2 years
Output	24 kW
Efficiency	Up to 98% (EN 92/42)

Related product manuals

Preview: Ferroli Bluehelix PRO C

Ferroli Bluehelix PRO C

Ferroli BLUEHELIX PRO 25C

Ferroli BLUEHELIX PRO S 32C

Ferroli BlueHelix THETA 24 C

Preview: Ferroli BLUEHELIX TECH S 45H

Ferroli BLUEHELIX TECH S 45H

Preview: Ferroli BLUEHELIX MAXIMA Series

Ferroli BLUEHELIX MAXIMA Series

Ferroli Ferella Boil F 24 MEL

Ferroli Ferella Boil F 30 MEL

Preview: Ferroli F24

Preview: Ferroli MODENA 27 C HE

Ferroli MODENA 27 C HE

Ferroli Domina Oasi F 24 E