To Next PageTo Next PageWhy is Ferroli Boiler showing a flame present signal when the burner is off?
If your Ferroli boiler indicates a flame is present even when the burner is off, it could be due to an electrode fault, so check the ionization electrode wiring. Alternatively, there could be a card fault, so check the card.
What causes fan fault in Ferroli Boiler?
A fan fault in your Ferroli boiler could stem from a couple of issues. First, check the 5-pin connector wiring to ensure there's a proper 230V power supply. If the power supply is fine, inspect the fan itself for damage and replace it if necessary.
How to troubleshoot specific combustion control errors in a Ferroli BlueHelix HiTech RRT C?
If you're experiencing specific combustion control errors with your Ferroli boiler, start by checking the fume ducts and condensate trap for any blockages. Ensure the gas supply pressure is correct. Perform a manual calibration to adjust the CO. If necessary, do a complete manual calibration. If the problem persists, replace the PCB.
What causes exchanger protection activation in Ferroli BlueHelix HiTech RRT C and how to solve it?
If the exchanger protection is activated on your Ferroli boiler, it may be due to a few reasons: Check the circulating pump and heating system to ensure proper water circulation. You may also need to vent the system to resolve poor circulation and anomalous flow probe temperature increases. Finally, check the exchanger and system for any blockages.
Why is there no flame after the ignition phase in my Ferroli BlueHelix HiTech RRT C?
If your Ferroli boiler fails to maintain a flame after ignition, the following could be the reasons: the ionization electrode may be faulty, so check its position, remove any deposits, and perform a manual calibration; replace the electrode if necessary. An unstable flame could also be the reason, so check the burner. Also, check for obstructions in the air/fume ducts and remove them. Make sure the trap isn't blocked, and clean it if necessary. Finally, wrong calibration could be the reason, so perform a complete manual calibration.
What to do if overtemperature protection intervenes in Ferroli BlueHelix HiTech RRT C?
If the overtemperature protection is activated in your Ferroli boiler, it could be due to several reasons. First, check that the heating sensor is correctly positioned on the flow pipe and operating properly; replace it if necessary. Also, ensure there is proper water circulation in the system by checking the circulating pump. Finally, vent the system to eliminate any air that may be trapped inside.
How to fix Ferroli BlueHelix HiTech RRT C when there is no burner ignition?
If your Ferroli Boiler isn't igniting, several factors could be the cause. First, check the gas flow to ensure it's reaching the boiler and that there's no air in the pipes. Next, inspect the ignition/detection electrode for proper wiring, positioning, and any deposits; replace if needed. Also, verify the gas supply pressure is sufficient. Ensure the trap isn't blocked and clean it if necessary. Check for obstructions in the air/fume ducts and remove them. If the issue persists, perform a complete manual calibration. Finally, check the gas valve and replace it if faulty.
How to resolve fume probe fault in Ferroli BlueHelix HiTech RRT C?
To address a fume probe fault in your Ferroli boiler, check the wiring or replace the fume probe if it's damaged.
How to fix gas valve connection problem in Ferroli BlueHelix HiTech RRT C?
To resolve a gas valve connection issue in your Ferroli boiler, ensure the gas valve connector is properly inserted. Check the wiring for any interruptions in the electrical connection between the control unit and the gas valve. If the gas valve is damaged, replace it.
Why Ferroli Boiler shows flame present signal with burner off?
If your Ferroli boiler is indicating a flame present signal when the burner is off, check the ionization electrode wiring and the condition of the electrode. Check the trap and clean it if necessary. Also, check the card.
General| Type | Condensing |
|---|---|
| Fuel Type | Natural Gas / LPG |
| Weight | 32 kg |
| Efficiency Class | A |
| Mounting | Wall-mounted |
| Modulation | 1:10 |
| Heat Exchanger Material | Stainless Steel |
| Control | Digital |
| Warranty | 2 years |
| Output | 24 kW |
| Efficiency | Up to 98% (EN 92/42) |
