Need help?Do you have a question about the Fiat X 1/9 1978 and is the answer not in the manual?
General| Brand | Fiat |
|---|---|
| Model | X 1/9 1978 |
| Category | Automobile |
| Language | English |
Procedure for checking and adjusting ignition timing.
Specifications for cylinder block and connecting rods.
Specifications for pistons, pins, and rings.
Specifications for the cylinder head.
Specifications for the camshaft and valve mechanism.
Specifications for crankshaft and main bearings.
Details on the carburetor.
Tightening specifications for engine components.
Procedure for removing the cylinder head with engine in car.
Procedure to check cylinder head gasket surface for distortion.
Procedure for inspecting and refacing valve seats and valves.
Procedure for checking cylinder bores.
Diagram and data for pistons and connecting rods.
Procedure for replacing the timing belt.
Details on the camshaft.
Procedure for replacing tappets and valve guides.
Procedure for removing the fuel pump.
Procedure for setting the float level.
Procedure for adjusting idle speed.
Procedure for adjusting idle CO.
Procedure for removing and installing the air injection manifold.
Details on the oil pump.
Procedure for replacing the oil filter.
Procedure for removing the radiator.
Procedure for removing and installing the water pump.
Details on the clutch release hydraulic control.
Information on the master cylinder.
Information on the operating cylinder.
Technical specifications for the clutch.
Procedure for checking clutch fluid level.
Procedure for bleeding the clutch circuit.
Procedure for adjusting the operating cylinder.
Group 212 covering transmission.
Group 274 covering the differential.
Group 331 covering wheel brakes.
Procedure for bleeding the hydraulic system.
Procedure for overhauling the brake master cylinder.
Procedure for replacing wheel brake calipers.
Procedure for overhauling the front brake caliper.
Procedure for overhauling the rear brake caliper.
Procedure for adjusting the hand brake.
Group 412 covering the steering system.
Procedure for disassembling the steering box.
Procedure for reassembling and adjusting the steering box.
Procedure for checking and adjusting front wheel toe-in.
Group 443 covering suspension and wheels.
Specifications for the front suspension.
Torque specifications for front suspension components.
Specifications for the rear suspension.
Torque specifications for nuts and bolt with car laden.
Procedure for front wheel alignment.
Procedure for rear wheel alignment.
Procedure for front wheel hub removal and installation.
Wiring diagram for the electrical system.
Group 551 covering engine ignition.
Group 552 covering engine starting system.
Group 553 covering the alternator.
Group 554 covering lighting system and fuses.
Group 555 covering accessories.
Specifications for the ignition system.
Specifications for the alternator.
Information on the ignition distributor.
Information on the starter motor.
Procedure for changing starter brushes.
Procedure for starter disassembly and assembly.
Procedure for replacing starter field coils.
Procedure for refacing the starter commutator.
Details on instruments and controls.
Information on the seat belt interlock system.
Troubleshooting for the battery and charging system.
Troubleshooting for the starting system.
Troubleshooting for the ignition system.
Troubleshooting for radiator and carburetor cooling systems.
Troubleshooting for seat belt interlock and key warning systems.
Troubleshooting for interior lights.
Troubleshooting for exterior lights.
Troubleshooting for vehicle instruments.
Troubleshooting the driver's seat switch.
Troubleshooting the driver's seat belt switch.
Troubleshooting the passenger's seat switch.
Troubleshooting the passenger's seat belt switch.
Troubleshooting the transmission switch.
Troubleshooting the indicator and buzzer relay circuit.
Troubleshooting the starter relay circuit.
Troubleshooting the oil pressure sender circuit.
Group 701 covering the body shell.
Group 711 covering interior trim and seats.
Procedure for checking and correcting body alignment.
Procedure for removing the door panel.
Procedure for adjusting door locks.
Procedure for removing and installing the back window.
Procedure for replacing and adjusting front luggage compartment lid.
Procedure for replacing and adjusting rear luggage compartment lid.
Procedure for replacing key lock.
Procedure for replacing and adjusting engine compartment lid.
Procedure for replacing and adjusting lid lock.
To Next Page
