Fimap MMg Series - User Manual

28 pages

Save Page as PDF

To Next Page

ORIGINAL INSTRUCTIONS DOC. 10063841 - Ver. AA - 09-2016

PROFESSIONAL SCRUBBING MACHINES

USE AND MAINTENANCE MANUAL

MMg

Main Page

Main Machine Components3
- Table of Contents4
Contents4
General Safety Regulations5
Symbols Used in the Manual9
Purpose and Content of the Manual9
Target Group9
Storing the Use and Maintenance Manual9
On Consignment of the Machine9
Introductory Comment9
Identification Data9
Technical Description9
Intended Use9
Safety9
Technical Data10
Symbols Used on the Machine11
Symbols Used on the Serial Number Plate11
Machine Preparation12
- Handling the Packaged Machine12
- How to Unpack the Machine12
- How to Move the Machine12
- Securing the Machine13
- Type of Battery to be Used13
- Battery Maintenance and Disposal13
- Inserting the Batteries into the Machine13
- Connecting Batteries to the System of the Appliance13
- Recharging the Batteries13
- Assembling the Squeegee14
- Filling the Solution Tank14
- Detergent Solution14
Preparing to Work14
Work14
- Scrubbing with Drying14
- Scrubbing Without Drying15
- Drying15
- Regulating the Detergent Solution15
- Reverse Gear16
- Extra Brush Head Pressure16
- Acoustic Signalling Device16
- Working Headlights (Optional)16
- Emergency Button16
- Hour Meter16
- Battery Charge Level Indicator16
- Lateral Brush 1Sl (Scrubbing Version)16
- Lateral Brush 2Sl (Sweeping Version)17
- Detergent Solution Recycling (Flr Version)17
- Overflow Device17
At the End of the Work17
Recommended Maintenance Operations17
- Emptying the Recovery Tank18
- Emptying the Debris Hopper (Sweeping Version)18
- Cleaning the Squeegee Body18
- Cleaning the Brush Head Brushes (Scrubbing Version)18
- Cleaning the Brush Head Brushes (Sweeping Version)18
- Cleaning the Lateral Brush (Scrubbing Version)19
- Cleaning the Lateral Brush (Sweeping Version)19
- Cleaning the Recovery Tank Filters19
- Cleaning the Recovery Tank19
- Cleaning the Debris Hopper (Sweeping Version)19
- Emptying the Solution Tank20
- Cleaning the Water System Filter20
- Cleaning the Vacuum Tube20
Extraordinary Maintenance Work21
- Assembling the Brush Head Brushes (Scrubbing Version)21
- Assembling Lateral Brush 1Sl (Scrubbing Version)21
- Assembling the Brush Head Brushes (Sweeping Version)21
- Assembling the Abrasive Pad (Orbital Version)21
- Replacing the Brush Head Brushes (Scrubbing Version)21
- Replacing the Brush Head Brushes (Sweeping Version)22
- Replacing Lateral Brush 1Sl (Scrubbing Version)22
- Replacing the Lateral Brush (Sweeping Version)22
- Replacing the Abrasive Pad22
- Replacing the Squeegee Unit Rubber Blades22
Disposal22
Adjustment Interventions23
- Adjusting the Squeegee Body'srubber Blades23
Ec Declaration of Conformity23
Troubleshooting24

Questions and Answers

A
Amanda HaynesAug 2, 2025
What to do if Fimap MMg Scrubber doesn't start?
- J
  Jennifer VillegasAug 2, 2025
  If your Fimap Scrubber doesn't start, first ensure that the main switch is in the "I" position; if not, turn the key a quarter turn clockwise. Also, check the battery charge level and recharge if critically low. Verify that the batteries are correctly connected to each other and that the battery connector is connected to the electrical system connector. If there are alarm messages on the control display when switched on, stop the machine immediately.
W
Wayne KiddAug 17, 2025
Why Fimap Scrubber batteries not charging correctly?
- H
  Holly BeltranAug 17, 2025
  If the batteries of your Fimap Scrubber are not charging correctly, check if the connector of the battery charger cable is properly inserted into the battery connector. Also, ensure that the plug on the battery charger's power cable is correctly inserted into the electrical outlet and that the characteristics of the mains power supply match those required by the battery charger. If the LEDs of the battery charger blink repeatedly, check the battery charger use and maintenance manual to find out what the flashing signals mean during the battery recharge stage.