Fimap MMx 50BT - User Manual

Questions and Answers

C
Charlene DuncanAug 14, 2025
What to do if there is insufficient water on the brushes of my Fimap Scrubber?
- D
  Dawn WoodsAug 14, 2025
  To address insufficient water on the brushes of your Fimap Scrubber, ensure the solution tank has water, which can be checked using the level indicator on the left rear of the device. Verify that the detergent solution tap is open by ensuring the lever on the rear of the appliance is fully rotated to the left (work direction). Also, confirm that the detergent solution tap on the brush head unit is in the active dosing system position, with the lever fully set to a vertical position. For FSS versions, ensure the water and detergent flow in the water system are not set to zero by turning the knobs to the right while the appliance is on. Finally, clean the solution tank filter on the rear of the appliance.
M
Mrs. Taylor ChapmanAug 17, 2025
Why is the squeegee on my Fimap Scrubber not drying perfectly?
- D
  Derek YoungAug 17, 2025
  If your Fimap Scrubber's squeegee isn't drying perfectly, start by ensuring the squeegee is clean. Check and adjust the squeegee settings as needed. Clean the entire vacuum unit, including the vacuum hose and vacuum motor filter float. If the rubber blades are worn, replace them. Make sure the cap on the recovery tank drainage hose is properly closed and that the suction cover is correctly positioned.
J
judithclarkAug 21, 2025
What to do if my Fimap Scrubber does not clean correctly?
- M
  mackenzie53Aug 21, 2025
  If your Fimap Scrubber isn't cleaning correctly, first ensure the appliance switches on correctly. Next, verify that the detergent solution is being supplied to the brushes adequately. Make sure the amount of detergent solution (for versions without FSS) or the amount of water and detergent (for versions with FSS) in the appliance's water system is appropriate for the task. Also, confirm that the brushes fitted on the appliance are suitable for the task and check their wear; replace them if the bristles are about 15mm long.
A
Amanda GrahamAug 25, 2025
How to fix a Fimap Scrubber that does not switch on?
- D
  David GillAug 25, 2025
  If your Fimap Scrubber is not switching on, check that the main switch is in the 'I' position; if not, turn the key a quarter turn to the right. Ensure no alarm message appears on the control display when starting the machine. Verify the battery is connected to the general system connector; if not, connect them. Finally, check the battery charge level on the control display and, if critical, perform a full charge cycle.
C
Charles MooreAug 27, 2025
What to do if the vacuum motor does not function on my Fimap Scrubber?
- C
  Calvin TaylorAug 27, 2025
  To address a vacuum motor that isn't functioning on your Fimap Scrubber, check if the recovery tank is full and empty it if necessary. Also, verify the proper functioning of the float inside the recovery tank.
J
Jerome MorganAug 30, 2025
Why is my Fimap Scrubber producing excessive foam?
- J
  John DickersonAug 31, 2025
  If your Fimap Scrubber is producing excessive foam in the recovery tank, check that a low-foam detergent is being used. If needed, add a small amount of antifoam liquid to the recovery tank. Remember that less dirty floors generate more foam, so the detergent solution should be more diluted in those cases.
S
Steven SandersSep 3, 2025
What to do if the batteries are not charged correctly on my Fimap Scrubber?
- A
  Adam SummersSep 3, 2025
  If the batteries of your Fimap Scrubber are not charging correctly, first check that the battery is connected to the general system connector; connect them if they are not. Verify that the battery charger is suitable for the batteries and correctly set up for the type of batteries used. Finally, refer to the battery charger's manual to understand the meaning of any flashing signals during recharge.
C
Courtney BryantSep 6, 2025
What to do if my Fimap Scrubber does not move?
- B
  barbarahigginsSep 6, 2025
  If your Fimap Scrubber does not move, ensure the appliance is switched on correctly. Check that the dead man's microswitches are active by actioning the dead man's levers below the handlebar control. In traction versions, verify that the forward speed adjustment knob is not set to the minimum.
C
Christina JacobsSep 10, 2025
Why does my Fimap Scrubber have a very low operating autonomy?
- J
  jenniferjordanSep 12, 2025
  If your Fimap Scrubber has very low operating autonomy, check that there is water in the solution tank, using the level indicator on the left rear of the device. Also, check the battery charge level on the control display and, if the charge level is critical, go through a full charge cycle.

Summary

GENERAL SAFETY REGULATIONS

Important Warnings for Safe Operation

Guidelines for label adherence, indoor use, authorized personnel, and avoiding inclines/rough floors.

Operational Precautions and Restrictions

Notes on temperature limits, socket requirements, and prohibitions like explosive atmospheres.

APPLIANCE PREPARATION AND SAFETY CHECKS

Ensuring Machine Safety

Critical safety checks before operation, including tank emptying and switch positions.

WORK PREPARATION AND SYSTEM ACTIVATION

Pre-Work Checks

Essential checks before starting work, including tanks, filters, and battery connection.

STARTING WORK AND ADJUSTING DETERGENT

Starting the Appliance

Procedures to safely start the machine after all preparation steps are completed.

END OF WORK PROCEDURES

DAILY MAINTENANCE PROCEDURES

Emptying Recovery Tank

Procedure for draining and emptying the recovery tank of waste water.

Emptying Solution Tank

Procedure for draining and emptying the solution tank.

Cleaning the Squeegee Body

How to clean the squeegee unit for optimal drying performance and vacuum motor longevity.

BRUSH CLEANING

Cleaning the Brush

Procedure for cleaning the brush to maintain performance and motor life.

FILTER AND COMPONENT CLEANING

Cleaning Vacuum Motor Filter Float

Steps to clean the filter float for optimal vacuum performance and motor life.

Cleaning Solution Tank Filter

Steps to clean the solution tank filter for water circuit longevity and cleaning efficiency.

WEEKLY MAINTENANCE - TANKS

Cleaning the Recovery Tank

Procedure to clean the recovery tank for improved appliance lifespan and performance.

Cleaning the Solution Tank

Procedure to clean the solution tank for improved appliance lifespan and performance.

EXTRAORDINARY MAINTENANCE - SQUEEGEE RUBBERS

Replacing Squeegee Rubber Blades

Step-by-step guide to replace the front and rear rubber blades of the squeegee.

EXTRAORDINARY MAINTENANCE - SQUEEGEE AND BRUSH

Replacing the Brush

Procedure for removing old brushes and installing new ones for optimal performance.

TROUBLESHOOTING - POWER AND BATTERY ISSUES

Alarm Message Display

Procedure for handling alarm messages shown on the control display.

Appliance Not Switching On

Steps to diagnose and fix issues preventing the appliance from powering on.

Battery Charging Problems

Troubleshooting steps for incorrect battery charging or low operating autonomy.

TROUBLESHOOTING - PERFORMANCE ISSUES

Appliance Movement Problems

Diagnosing and fixing issues related to the appliance not moving or having insufficient traction.

Cleaning and Drying Performance

Troubleshooting steps for insufficient water, poor cleaning, or imperfect drying by the squeegee.

TROUBLESHOOTING - FOAM, VACUUM, AND PUMP ISSUES

Vacuum Motor Not Functioning

Steps to diagnose and resolve issues with the vacuum motor not operating.

Fimap MMx 50BT Specifications

General

Model	MMx 50BT
Category	Scrubber
Power Supply	Battery
Battery Voltage	24 V
Brush Motor Power	400 W
Maximum Speed	5 km/h
Squeegee Width	800 mm
Solution Tank Capacity	50 L
Traction	Automatic
Bluetooth	Yes
Working Width	510 mm
Tank Capacity	50 L