EasyManua.ls Logo

Fimap FIMOP - User Manual

Fimap FIMOP
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
COMMERCIAL AUTOSCRUBBER
ORIGINAL INSTRUCTION DOC. 10053541 - Ver. AA - 06-2015
FIMOP
USE AND MAINTENANCE MANUAL

Table of Contents

Other manuals for Fimap FIMOP

Preview: Technical News
Technical News8 pages

Questions and Answers

  • J
    James CallahanJul 25, 2025
    What to do if my Fimap FIMOP does not clean correctly?
    • J
      Jennifer SotoJul 25, 2025
      If your Fimap Scrubber isn't cleaning correctly, consider the following: * Make sure the appliance switches on. Refer to the troubleshooting steps for 'THE APPLIANCE DOES NOT SWITCH ON'. * Ensure an adequate amount of detergent solution is being dispensed. See the troubleshooting steps for 'NOT ENOUGH DETERGENT SOLUTION ON THE BRUSH'. * Verify the brush is correctly inserted. * Inspect the brush for wear and replace if necessary.
  • M
    Michael AllenJul 29, 2025
    Why is my Fimap FIMOP Scrubber battery not charging correctly?
    • C
      Christopher SharpJul 30, 2025
      If the battery of your Fimap Scrubber isn't charging correctly, check these items: 1. Confirm the power supply cable plug is correctly inserted into the battery charger base socket. 2. Ensure the power supply cable plug is properly connected to the mains socket. 3. Verify that your power supply network is compatible with the battery charger requirements. 4. If the LED on the battery charger base flashes repeatedly, consult the battery charger use and maintenance manual to understand the meaning of the flashing signals during the battery recharge stage.
  • S
    stanleymillerAug 3, 2025
    What to do if the squeegee on my Fimap FIMOP does not dry perfectly?
    • C
      Christopher MillerAug 3, 2025
      If the squeegee on your Fimap Scrubber isn't drying perfectly, try the following: * Remove any obstructions from the squeegee. * Clear any blockages from the vacuum duct. * Check the recovery tank cover for obstructions. * Ensure the recovery tank cover is correctly positioned.
  • E
    Emily ShepardAug 7, 2025
    Why is my Fimap FIMOP Scrubber not vacuuming correctly?
    • C
      Christina HamiltonAug 7, 2025
      If your Fimap Scrubber isn't vacuuming correctly: * Empty the recovery tank. * Check for and clear any obstructions, referring to the section 'THE SQUEEGEE DOES NOT DRY PERFECTLY'.
  • J
    jeffreylewisAug 11, 2025
    How to increase detergent solution on the brush of my Fimap Scrubber?
    • A
      Amy FullerAug 11, 2025
      If there's not enough detergent solution on the brush of your Fimap Scrubber: * Fill the solution tank with detergent. * Remove any obstructions from the detergent solution filter.
  • S
    Susan RomeroAug 16, 2025
    Why is my Fimap FIMOP Scrubber producing excessive foam?
    • E
      Emily DanielsAug 16, 2025
      If your Fimap Scrubber is producing too much foam: * Ensure you are using a low-foam detergent. If not, switch to one and consider adding a small amount of antifoam liquid to the recovery tank. * If the floor isn't very dirty, dilute the detergent inside the solution tank.
  • Z
    Zachary ClarkAug 20, 2025
    What causes low operating autonomy in Fimap FIMOP?
    • K
      Kenneth SmithAug 20, 2025
      If the operating autonomy of your Fimap Scrubber is very low, ensure that the battery charge level is not critical. If it is, perform a complete recharge cycle.

Summary

SYMBOLS USED IN THE MANUAL

SYMBOLS USED ON THE APPLIANCE

Explains symbols found on the appliance itself for operation and identification.

MANUAL OVERVIEW AND INITIAL INFORMATION

INTENDED USE

Defines the specific applications and limitations for which the appliance is designed.

SAFETY

Outlines crucial safety precautions for operating and maintaining the appliance.

TECHNICAL DESCRIPTION

Provides a detailed overview of the appliance's mechanical and functional aspects.

SERIAL NUMBER PLATE

Details the location and importance of the appliance's serial number for identification.

TECHNICAL DATA AND SPARE PARTS

SPARE PARTS

Lists essential spare parts for the appliance with corresponding codes and quantities.

GENERAL SAFETY REGULATIONS

HANDLING AND TRANSPORT

HOW TO UNPACK THE APPLIANCE

Step-by-step instructions for safely removing the appliance from its packaging.

HOW TO TRANSPORT THE APPLIANCE

Procedures for securely moving the appliance, including folding and securing.

BATTERY MANAGEMENT

RECHARGING THE BATTERY

Detailed instructions on how to safely charge the appliance's battery.

PREPARING THE APPLIANCE

PREPARING TO WORK

OPERATING THE APPLIANCE

POST-OPERATION PROCEDURES

MAINTENANCE AND CLEANING

TROUBLESHOOTING

DISPOSAL

EC DECLARATION OF CONFORMITY

Fimap FIMOP Specifications

General IconGeneral
WeightNot available
Working WidthNot available
Tank CapacityNot available
Solution tank capacity3 l / 0.8 gal
Recovery tank capacity3 l / 0.8 gal
Power supply36V
Battery voltage36 V

Related product manuals