Fimap GL Pro - User Manual

Questions and Answers

T
Troy DayAug 13, 2025
How to troubleshoot a Fimap Scrubber that does not start?
- R
  Rebecca KentAug 13, 2025
  If your Fimap Scrubber machine isn't starting, there might be a few reasons: * The machine could be in stand-by mode. Try pressing the stand-by button to activate or deactivate it. * There might be alarm messages on the command display when you switch it on. If this is the case, stop the machine immediately and contact a specialized service center. * The batteries may not be correctly connected. Ensure they are properly connected to each other and that the battery connector is connected to the electrical system connector. * The battery charge level might be too low. If it's critical, perform a complete charge cycle.
C
Carolyn VazquezAug 16, 2025
Why is my Fimap Scrubber not cleaning correctly?
- L
  lesteredwardAug 16, 2025
  If your Fimap Scrubber isn't cleaning correctly, it could be due to several factors: * Not enough detergent solution is being dispensed. Refer to the section on insufficient detergent solution on the brushes. * The brushes might not be correctly inserted. Ensure that the disc brushes are properly inserted inside the machine. * The brush bristles might be excessively worn. Inspect the brushes and replace them if necessary.
J
Jeremiah Hamilton IVAug 20, 2025
What to do if the squeegee on my Fimap GL Pro Scrubber does not dry perfectly?
- A
  asmithAug 20, 2025
  If the squeegee on your Fimap Scrubber isn't drying perfectly, consider these possibilities: * The vacuum unit could be obstructed. Check the squeegee for any blockages. * The vacuum tube might be blocked. Ensure the vacuum tube is free from obstructions. * The filters in the recovery tank could be clogged. Check that the filters in the recovery tank are free from obstructions. * The cap on the recovery tank drainage tube might not be positioned correctly. Make sure the cap is properly positioned. * The recovery tank lid might not be correctly positioned. Ensure the lid is properly placed on the machine.
C
Cassandra DavisAug 25, 2025
Why is my Fimap Scrubber not vacuuming correctly?
- B
  Becky CooperAug 25, 2025
  If your Fimap Scrubber is not vacuuming correctly: * The recovery tank might be full. Empty the recovery tank. * There might be an issue with the squeegee. Refer to the section on what to do if 'THE SQUEEGEE DOES NOT DRY PERFECTLY'.
M
millertammyAug 27, 2025
Why is my Fimap GL Pro producing excessive foam?
- J
  Jessica SmithAug 28, 2025
  If you're experiencing excessive foam production with your Fimap Scrubber: * The detergent you're using might not be suitable. Ensure you're using a low-foam detergent and, if needed, add a small amount of anti-foam liquid to the recovery tank. * The floor might not be very dirty. Try diluting the detergent more.
D
Daniel WilliamsonAug 31, 2025
What causes insufficient detergent solution on the brushes of my Fimap GL Pro?
- R
  Rebecca MullinsSep 1, 2025
  If you're not getting enough detergent solution on the brushes of your Fimap Scrubber, it could be because: * The amount of detergent solution in the water system isn't sufficient. Check that you have enough solution for the work you're doing. * The detergent solution filter is obstructed. Check the filter and clean it if it's clogged.
B
Brian SmithSep 4, 2025
How do I fix Fimap GL Pro Scrubber batteries not charging correctly (without on-board charger)?
- J
  Jacqueline BarnettSep 4, 2025
  If the batteries on your Fimap Scrubber (versions without an on-board battery charger) aren't charging correctly: * The connector of the battery charger cable might not be properly inserted. Reconnect the battery charger cable connector to the battery connector. * The plug on the battery charger's power cable might not be correctly inserted into the electrical outlet. Ensure the plug is connected to the mains socket. * The mains power supply characteristics might not match what the battery charger requires. Verify that the characteristics on the battery charger plate match those of the mains supply. * The LEDs on the battery charger might be blinking repeatedly. Consult the battery charger's manual to understand the meaning of these flashing signals during the recharge stage.