18 FIRECLASSAddressableFireControlPanel FC501
Figure 6 - Autoaddressing procedure.
■ Programming Device Addresses Using the
Programmer
As an alternative to the procedure of Auto-addressing
the Installer can use the service tool FC490ST to ad-
dress the devices on Loop.
1. Connect your detector to the programmer. If you
need to program a sounder or a module, con-
nect the programming lead into the AUX port of
the programmer and the other end of the lead into
the device‘s programming port
Note you cannot address a detector while the pro-
gramming lead is plugged in.
2. Press and hold F1 to switch the programmer on.
3. When prompted, enter the password: F1, F2, F1,
F2, F3, F4.
4. Press F2 to enter the address program, this will
show the current address of the device on the
screen (brand new devices will always be 255).
5. Press F2 to choose the “write” menu option.
6. Using F3 and F4, change the address to the
required address.
7. When the correct address is displayed, press F2
to write.
8. The programmer will display the message: “pro-
grammed ok” and then it will show the next ad-
dress.
9. Label the device ready for installing.
DEVICE MAPPING RUNNING 0=stop
Evt time type add counter 017
016 10:15:33 PH L1:---
017 10:17:19 PH L1:---
AUTO ADDRESSING END
Found: 018 detectors, 004 modules
ENT to DEVICE MAPPING, ESC to exit
DEVICE MAPPING STOPPED 1=run
Evt time type add done:000/022
001>10:15:33 PH L1:---< enter the add.
002 10:17:19 PH L1:--
-
DEVICE MAPPING STOPPED 1=run
Evt time type add done:017/022
--- un
que
:---
en
er
e a
.
--- unique LPAV L2:---
=run
v
me
ype a
one:
/
:
:
:
o con
g.
002 10:17:19 PH L1:---
DEVICE MAPPING STOPPED 1=run
Evt time type add done:020/022
---
*ac
ve*
:---
en
er
e a
.
--- --:--:--LPSB L3:---
=run
v
me
ype a
one:
/
--
un
que
:
o con
g.
--- unique LPAV L2:---
=run
v
me
ype a
one:
/
--
--:--:--
:
o con
g.
--- --:--:--LPSB L3:---
EXIT
MAIN PAGE
DEVICE MAPPING PHASE
BASIC DEVICE
CONFIGURATION PHASE
AUTO ADDRESSING RUNNING
PLEASE WAIT
ESC to exit
Master panel Lev.3: Program
Detector: 50 Modules: 44
Iloop=073 mA (400ma MAX)
Not addressed dev.> ENT to AUTO-ADDRES
S
PANEL IS READY TO WORK
AT THIS TIME
(with the default basic programming)
:
e
ev.
:
WORKING MODE Master panel
[First flo ]
^
:
e
ev.
:
DEVICE NAME Master panel
:
e
ev.
:
ASSIGNED ZONE Master panel
[First flo ]
^
:
e
ev.
:
DEVICE NAME Master panel
[First flo ]
^
:
e
ev.
:
as
er pane
[First flo ]
^
MS: Det 089 lev.3 :PROGRAM
DEVICE NAME Master panel
:
e
ev.
:
as
er pane
[First flo ]
^
:
e
ev.
:
DEVICE NAME Master panel
:
e
ev.
:
as
er pane
[First flo ]
^
:
e
ev.
:
DEVICE NAME Master panel
[First flo ]
^
:
e
ev.
:
as
er pane
[First flo ]
^
MS: Det 089 lev.3 :PROGRAM
DEVICE NAME Master panel
:
e
ev.
:
as
er pane
[First flo ]
^
:
e
ev.
:
DEVICE NAME Master panel
:
e
ev.
:
as
er pane
[First flo ]
^
:
e
ev.
:
DEVICE NAME Master panel
[First flo ]
^
BY WALKING
(Panel +installer)
ESC
ESC
ESC
0
EXIT
MAIN PAGE
DEVICE ACQUIRING
BY DEVICE
EXIT
FAULT PAGE
(not addressable devices)
ESC
EXIT
FAULT PAGE
(not addressable devices)
Notes
"Unique" in the time field indicates that it is the only device of its type on the
loop. For example if only one FC410DDM module is used in the system, it is
tagged as "Unique" so it is not necessary to activate it, the installer knows
where it is.
"Active" in the time field indicates that the relevant device is active, it is
applicable ONLY to output device types such as sounders, beacons and SNM
modules.
When the installer, scanning the list of previously auto-addressed devices,
reaches an output-only device type, this device becomes active (a sounder
starts to sound, a beacon starts to flash, an output module illuminates its
LED) until a new device is selected or the permanent address is entered. In
this way it will be possible to locate where the device is.
To Next Page
Loading...
