https://
install.myfirstech.com
Copyright 2020 Fi rste ch, LLC. “Hello, my name is Inigo Montoya....” Page
51
3-15 Soft Disarm: this feature will enable Factory Alarm Arm (FAA) and Factory Alarm Disarm (FAD)
outputs to trigger when silencing the Compustar siren when sounding with full alarm.
FO1 - Off: (Default) this will keep the standard Compustar soft disarm operation. Soft disarm feature
allows the user to silence the Compustar siren as its sounding with full alarm without fully disarming the
system which may unlock the doors and leave the vehicle unsecure.
FO2 - On: this option will provide a FAD output on both data and analog connections, when the
user taps the unlock/disarm once to silence the Compustar system while it’s sounding, so it will disarm
any factory alarm that may be sounding as well. In case the FAD function unlocks the doors the CMX
will send the FAA on both data and analog connections 5 seconds later to make sure the vehicle is
re-locked and secure. (This feature works well with GM, Chrysler, Dodge, Jeep, Toyota, Lexus vehicles
that may have factory security.)
FO3 – Disarm with 1 press: This option will allow the user to completely disarm the system once it is
sounding on the first unlock command. When set to this option the CM will unlock and send the FAD
commands on the first disarm/unlock press from a Firstech remote.
3-16 RPS-KP2: (Remote Paging Sensor) this feature sets the RPS-KP2 hardware being used with the CMX.
FO1 - RPS Touch: (default) this option enables the RPS touch functions when using the RPS touch
hardware with the CMX. RPS Touch will support a 4 digit code that when entered can be used to
arm/lock and disarm/unlock a CMX or page a Firstech remote or accessory. Please refer the RPS
section of this manual or the RPS product manual for installation and operation of the RPS touch
hardware.
FO2 – KP2: This option enables the latest Keyless entry paging window sensor KP2 function on the
CMX. This Sensor will support 4-6 digit code that when entered can be used to arm/lock and
disarm/unlock a CMX or page a Firstech remote or accessory.
FO3 - RPS Touch NO LED FLASH WHILE ARMED: This option enables the RPS touch functions
when using the RPS touch hardware with the CMX, but the LED WILL NOT FLASH WHILE
ARMED.
FO4 – KP2 NO LED FLASH WHILE ARMED: This option enables the KP2 functions when using
the KP2 hardware with the CMX, but the LED WILL NOT FLASH WHILE ARMED
3-17 Normally Open (N/O) Secure Start Output Timer: Secure Start feature will provide an output from
any POC set to Secure Start N/O [32]. This output will send (-) 250mA for the time selected by one of
the options below.
It is designed to be used with our FTI SPTS (secure Push To Start) vehicle disable T harnesses. In its
rest state the vehicle disable harness will disable the PTS button until the driver is ready to use it.
NOTE: The Vehicle will not be able to go to ignition on until the system is disarmed/unlocked
Once the CMX is unlocked/disarmed the N/O output will energize the SPTS harness making the PTS
button available for use for the preselected time, or until the CMX is armed/locked. Once Ignition on is
detected the output will remain latched until Ignition has been turned off and the preselected time
has expired or the system has been armed/lock using a Firstech remote, Drone, KP sensor, OEM
remote (supporting idatalink firmware only), or passive arming.
-NOTE: When using the N/O option be sure to select a timed output that will be most convenient
for your customer. IF the timer runs out, they MUST disarm/unlock again to re-activate the
Secure Start Output.
To Next Page
Loading...