flamco Midi 225D - User Manual

Questions and Answers

M
Michael WilsonAug 20, 2025
What to do if LOW H20 fault is displayed on flamco Midi 225D?
- D
  dixonrobertAug 20, 2025
  If the LOW H20 fault is displayed on your Flamco Portable Generator, here are a few things you can check: * Make sure the mains water supply to the unit is turned on. * The fault will clear once the break tank has been re-filled if the mains pressure is poor. * Remove any non-standard electrical connections from terminals 19 & 20. * Consider replacing the low water float switch, or the digital controller if they have failed.
J
jgarciaAug 22, 2025
Why pressure reading does not match actual system pressure on flamco Midi 225D?
- S
  Susan Scott MDAug 22, 2025
  If the pressure reading on your Flamco Portable Generator doesn't match the actual system pressure, there might be a few reasons: * Ensure the internal isolation valve within the unit is open. * Review the SENSOR TYPE setting. * Remove any non-return valve installed between the unit and the system. * The pressure sensor might have failed and needs replacement.
M
Matthew LopezAug 25, 2025
What causes HIGH PRESSURE fault on Flamco Portable Generator?
- K
  Kristen FranklinAug 25, 2025
  If your Flamco Portable Generator displays a HIGH PRESSURE fault, it could be due to a few reasons: * Check the expansion vessel pre-charge and re-charge if necessary. * Review the expansion vessel selection, as it might be undersized. * Review the system specifications, as the HIGH PRESSURE set point might be too low.
J
Jennifer RodriguezAug 26, 2025
How to fix pump that runs but does not make up pressure in flamco Midi 225D Portable Generator?
- L
  lawrencebrentAug 26, 2025
  If your Flamco Portable Generator's pump runs but doesn't build up pressure, it might be air-locked. Try bleeding the pump to resolve this.
S
Sean CooperAug 27, 2025
What to do if system pressure has risen above the HIGH PRESSURE set point in flamco Midi 225D?
- J
  James ReyesAug 27, 2025
  If the system pressure of your Flamco Portable Generator has risen above the HIGH PRESSURE set point, decrease the system pressure using a suitable drain point.
E
Elizabeth GregoryAug 29, 2025
What causes HIGH H20 fault on flamco Midi 225D Portable Generator?
- L
  Lauren BoydAug 29, 2025
  If your Flamco Portable Generator displays a HIGH H20 fault, it could be due to: * A non-standard electrical connection into terminals 21 & 22. Remove any such connections. * A failure of the digital controller, which would require replacement.
A
angela35Aug 31, 2025
What to do if ERROR 1 fault is displayed on flamco Midi 225D Portable Generator?
- S
  Shelly ShepherdAug 31, 2025
  If you see 'ERROR 1 fault' displayed on your Flamco Portable Generator, check the SENSOR TYPE option and review its setting. Also, the pressure sensor might have failed and require replacement.
K
keith16Sep 2, 2025
Why is the pump persistently becoming air-locked in flamco Midi 225D?
- E
  Elizabeth BatesSep 2, 2025
  If your Flamco Portable Generator's pump is persistently becoming air-locked, check the float valve flow restrictor selection, especially if you have mini and midi units.
M
Margaret PadillaSep 4, 2025
Why is the break tank overfilling in Flamco Portable Generator?
- M
  Martin CostaSep 4, 2025
  If the break tank in your Flamco Portable Generator is overfilling and discharging water, consider the following: * Check the float valve flow restrictor selection (mini and midi units only). * Set the float valve to its lowest possible position. * The float valve might have failed and needs replacement. * A pump non-return valve might have failed and needs replacement.
J
Jason SchwartzSep 6, 2025
Why is the pump repeatedly running in short bursts in flamco Midi 225D?
- D
  David WhiteSep 6, 2025
  If your Flamco Portable Generator's pump is repeatedly running in short bursts, it could be due to: * The internal isolation valve within the unit being partially closed. Fully open it. * Too much restriction in the connecting pipe work. Increase bore, reduce bends, or reduce length. * A pump non-return valve has failed, replace it. * The expansion vessel has failed or lost its pre-charge, check and re-charge if necessary. * The unit's connection point is too far from the expansion vessel. Move them closer.