Flex QQ Extra 300 - Receiver Installation;Servo Connections

7
RECEIVER INSTALLATION/SERVO CONNECTIONS
For the latest Aura Features, programs, transmitter downloads, and instructions, please visit www.exinnovations.com/aura. To connect
modern data-linked receivers, follow these instructions. For traditional PWM receivers, refer to the connection diagram at the bottom.
1. Plug the left aileron servo into the S2 port on the Aura 8 and the right aileron servo into the S3 port.
2. Install the receiver in the fuselage using either Velcro tape or double-sided foam tape (not included)
3. Connect the receiver to the Aura 8 using the appropriate connection illustrations below.
DSM2/DSMX REMOTE RECEIVER
Connect one remote DSM2/DSMX receiver to antenna port ‘A’ on
the side of the unit. Attach the remote receiver securely to the
fuselage using hook-and-loop tape or double sided foam tape.
PWM (TRADITIONAL) RECEIVER PORT CONNECTIONS
Refer to the chart below for channel mapping for traditional
receiver connections for receivers not specically supported.
Male to male extensions* are used for the following connections.
Lead to ESC/BEC
Leads to ight
control servos
ESC WILL CONNECT DIRECTLY TO
THE RECEIVER. NO CONNECTION
FROM THE AURA TO RECEIVER
WILL BE MADE FOR THE ESC.
CONTROL SURFACE
AURA 8
RECEIVER
AURA 8
CH 5 (Gear) S4
Aileron
S1
Rudder
S3
Left Aileron
S5
Right Aileron
S6
Rudder
S8
Elevator
S7
Elevator S2
CONNECTIONS IN CONNECTIONS OUT
§ Works conveniently with all major radio systems
§ Accepts signals from DSM Satellite(s), Futaba S.Bus ,
Graupner Hott, JR XBus, PPM stream, or any brand of
Rx via male to male servo connectors
§ Expertly tuned and ready to use
§ USB port allows loading model congurations, user
programming, and rmware updates (cable included)
§ Flexible and extensive programming through PC or
mobile device (iPhone®/Android™)
§ 3+ ight modes allow precise or aggressive settings to
be selected in ight
§ 3-axis gyro utilized in QQ Extra 300 programming
§ Powerful 32-bit processor and 6 axis sensor for future
updates and re-use
The Aura 8 advanced ight control system installed in your QQ Extra 300
is a giant leap forward in aircraft ight control system technology.
Compatible with virtually every receiver on the market today via PWM
connections, the Aura features special conguration for DSM systems
via remote receiver connection, and serial data connection for Futaba
S.Bus, Graupner HOTT, and JR XBus systems.
The Aura 8 advanced ight control system in your QQ Extra has been
pre-tuned for ease of use, eliminating many hours of setting gains.
For
the latest Aura Features, programs, transmitter downloads, and
instructions, please visit www.exinnovations.com/aura.
The Aura is programmable through either PC or mobile device and
every axis has independent gain adjustment and by each ight mode.
All dual rate, expo, travel, and mode programs are adjusted inside the
Aura through the PC/mobile application. An assignable master gain
that is OFF by default can be enabled by the Aura application. If
desired, assign it to CH 8/AUX 3 on a proportional dial or slider.
By default CH5/Gear is used to select the 3 ight modes by 3 position
transmitter switch.
AURA 8 ACFS
*(FPZAU01 3pc Male to Male Servo Cable/S.Bus) not included | ‡ non-PWM connections
FUTABA S.BUS/GRAUPNER HOTT/JR XBUS CONNECTION
Connect the included male to male extension to the receiver’s data
port and connect to port ‘B’ on the face of the unit. Refer to your
radio manufacturer’s instructions for specic information on
appropriate serial port connections and system settings.
DEFAULT CONNECTIONS ‡
S1 Throttle (ESC/BEC)
S2 Left Aileron
S3 Right Aileron
S4 Elevator
S5 Rudder