Fluke 1AC II VoltAlert

To Next Page

1AC II

VoltAlert

Instruction Sheet

Read First: Safety Information

WX Warning

To avoid possible electric shock or personal injury:

If the Tester is used in a manner not specied by the manufacturer, protection ●

provided by the Tester may be affected.

Do not use if VoltBeat is not ashing. ●

Test on a known live source within the rated ac voltage range of the product, ●

both before and after use to ensure unit is in good working condition.

When using the Tester, if tip does not glow, voltage could still be present. ●

The Tester indicates active voltage in the presence of electrostatic elds of

sufcient strength generated from the source (MAINS) voltage. If the eld

strength is low, the Tester may not provide indication of live voltages. Lack of

an indication occurs if the Tester is unable to sense the presence of voltage

which may be inuenced by several factors including, but not limited to:

Shielded wire/cables ●

Thickness and type of insulation ●

Distance from the voltage source ●

Fully-isolated users that prevent an effective ground ●

Receptacles in recessed sockets/ differences in socket design ●

Condition of the Tester and Batteries ●

Do not use if the Tester appears damaged or if the Tester is not operating ●

properly. Specically examine the probe tip for cracks or breakage before use.

If in doubt, have the Tester serviced.

Do not apply more that the rated voltage as marked on the Tester. ●

Use caution with voltages above 30 V ac as a shock hazard may exist. ●

Comply with local and national safety requirements. ●

Use proper protective equipment as required by local or national authorities. ●

Table 1. Symbols

Double Insulated.

Hazardous Voltage. Risk of electric shock.

Risk of danger. Important information. See Instruction Sheet.



Conforms to relevant Canadian and US Standards.



Conforms to relevant European Union directives.



Conforms to relevant Australian standards.



Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website

for recycling information.

CAT IV Equipment is designed to protect against transients from the primary supply level.

(i.e. - electricity meter or overhead /underground utility service).

Safety Compliance: Meets IEC 61010-1:2001, UL 61010-1 (2nd ed.), CAN/CSA-C22.2

No. 61010-1-04, and ISA-82.02.01

EMC Compliance: Meets IEC 61326-1:2006

Operating: 90 V ac to 1000 V ac (A1/A2), 200 V to 1000 V ac (E1/E2/P1), 20 V to 90 V

ac (LAC)

Temperature: Operating: -10 to 50 °C Storage: -10 to 50 °C

Humidity: 0 % to 95 % (0 to 30 °C)

Altitude: 3000 m

Pollution Degree: 2

PN 3499948

July 2009

FOR USE BY COMPETENT

PERSONS

Anyone using this instrument should be

knowledgeable and trained about the risks

involved with measuring voltage, especially

in an industrial setting, and the importance of

taking safety precautions and of testing the

instrument before and after using it to ensure

that it is in good working condition.

Main Page

Need help?

Do you have a question about the Fluke 1AC II VoltAlert and is the answer not in the manual?

Summary

Safety Information

General Warnings and Precautions

Safety warnings to avoid electric shock or personal injury, including tester usage and conditions.

Symbol Definitions

Explains various symbols used on the product and their meanings, such as double insulation and risk of danger.

Safety and Compliance Standards

Lists safety compliance standards (IEC, UL, CSA) and EMC compliance, along with operating specifications.

Operating Instructions

Powering the Tester On and Off

Instructions for activating and deactivating the tester, including confirmation signals.

Tester Features and Functions

Details on VoltBeat self-test, voltage detection, auto power off, beeper control, and low battery alerts.

Maintenance and Support

Guidance on cleaning the instrument and contact information for technical support and service.

Limited Warranty and Liability