EasyManuals Logo

Flymo EasiLife User Manual

Flymo EasiLife
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
A
C
B
3.10.6.1 To set the Lawn Coverage function
1. Do steps 1–3 in
To get access to the menu on
page 21
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area 1-3
.
3. Use the arrow button to select the area.
4. Push the OK button.
5. Measure the distance from the charging station
to the start of the area. Measure along the guide
wire. Refer to
To measure the distance from the
charging station on page 24
.
6. Push the arrow buttons to select the distance,
measured in m.
7. Push the OK button.
8. Use the arrow buttons to select the percentage of
the cutting time the product must cut the area. The
percentage is equal to the percentage of the area
in relation to the complete work area.
a) Measure the area.
b) Divide the measured area with the total work
area.
c) Convert the result to percentage.
Note:
The sum of Area 1-3 must be 100% or
less. If the sum is less than 100%, the product
sometimes straddles the guide wire and starts to
mow at the starting point. Refer to
Starting point on
page 25
.
9. Push the BACK button.
3.10.6.2 To set the PassageSense function
Note:
To prevent that the grass in the narrow passage
is worn, Flymo recommends to set a low percentage for
the
PassageSense
.
1. Do steps 1–3 in
To get access to the menu on
page 21
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area 1-3
.
3. Use the arrow buttons to select the area.
4. Push the OK button.
5. Measure the distance from the charging station
to the beginning of the narrow passage. Measure
along the guide wire. Refer to
To measure the
distance from the charging station on page 24
.
Note: Make sure that the distance to the
PassageSense
is set inside the narrow passage.
6. Push the arrow buttons to select the distance.
7. Push the OK button.
8. Use the arrow buttons to select the percentage
of the cutting time that the product must start the
narrow passage cutting.
9. Use the arrow buttons and the OK button to select
More > PassageSense
.
10. Push the OK button to enable
PassageSense
.
11. Push the BACK button.
3.10.6.3 To do a test of the Lawn Coverage function
1. Put the product in the charging station.
2. Do steps 1–3 in
To get access to the menu on
page 21
.
3. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area 1-3 > More > Test
.
4. Push the OK button.
5. Push the GO button.
6. Close the hatch.
7. Make sure the product can find the area.
3.10.6.4 To measure the distance from the charging
station
1. Put the product in the charging station.
2. Do steps 1–3 in
To get access to the menu on
page 21
.
3. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area 1-3 > How far?
4. Use the arrow buttons to set 500 m / 540 yd as a
distance.
5. Push the OK button.
6. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area 1-3 > More > Test
.
7. Push the OK button.
24
- Installation 1392 - 007 -

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Flymo EasiLife and is the answer not in the manual?

Flymo EasiLife Specifications

General IconGeneral
TypeRobotic Lawn Mower
Cutting Width16 cm
Cutting Height20-50 mm
Typical Mowing Time on One Charge65 min
Battery TypeLithium-Ion
Battery Voltage18 V
Pin CodeYes
Lift SensorYes
Tilt SensorYes
Battery Capacity2.1 Ah
Typical Charging Time60 minutes
Sound Level Guaranteed (LWA)58 dB

Related product manuals