FROG Leap Twin - User Manual

Other manuals for FROG Leap Twin

Manual18 pages

Questions and Answers

C
Christine HillAug 12, 2025
How to fix under chlorinating with FROG Leap Torpedo Pac?
- C
  Christine WilliamsAug 13, 2025
  If you're under-chlorinating with the FROG Leap Torpedo Pac and can't maintain a chlorine level of 0.5 to 1.0 ppm, first, ensure that there are chlorine tablets in the Torpedo Pac and that it's installed correctly. If a correction was made, test the water in 24 hours. If the chlorine level is still low, turn the dial up one setting and test the water again in 24 hours, continuing to raise the setting by one increment each day until you achieve the proper reading. Check for suction side leaks by looking for air bubbles in your pump basket or at the return jet. Ensure the pump runs for at least 6 hours on high speed (40 gpm or higher) or bleed the air from the back time cap if it is open.
G
gmullinsAug 16, 2025
How to fix cloudy water in FROG Leap Lighting Equipment?
- J
  Jessica LittleAug 16, 2025
  If the water in your FROG Leap Lighting Equipment appears cloudy, ensure your filtration system is functioning correctly by cleaning the filter, skimmer, and pump basket. Additionally, verify that the pool is properly balanced. Shocking the water can help eliminate any buildup of organic matter. Also, ensure adequate circulation time by increasing pump time if necessary.
J
James Velez MDAug 20, 2025
Why did the water in my FROG Leap Lighting Equipment turn color?
- W
  Wendy HollandAug 20, 2025
  If the water in your FROG Leap Lighting Equipment changes color, it could be due to metals in the fill water oxidizing. In this case, have the pool water tested. Alternatively, shock the pool, increase circulation time if needed, and clean the filter until the water clarity returns.
J
juanhollandAug 25, 2025
What to do if FROG Leap Lighting Equipment is under chlorinating?
- J
  Jasmine JacksonAug 25, 2025
  If you are under-chlorinating with the FROG Leap® Torpedo Pac®, and unable to maintain 0.5 to 1.0 ppm, first ensure there are chlorine tablets in the tower areas of the FROG Leap® Torpedo Pac® and that it is installed properly. Check for a suction side leak by looking for air bubbles in your pump basket or at the return jet. If still low, turn the dial up one setting and test the water again in 24 hours. Make sure pump run time is at least 6 hours on high speed (40 gpm or higher).
J
James PalmerAug 27, 2025
How to remove algae from FROG Leap Lighting Equipment?
- P
  paulwoodsAug 27, 2025
  If algae forms in or on your FROG Leap Lighting Equipment, use a nonmetallic (polyquat) algaecide per the directions on the bottle and brush the sides of the pool often. Also, clean the filter and shock the pool with chlorine daily until water clarity returns.
E
Eric HarveyAug 31, 2025
What to do if chlorine is too high in FROG Leap Lighting Equipment?
- X
  xharrisAug 31, 2025
  If the chlorine reading is over 3.0 ppm, remove the Torpedo Pac[®] from the FROG Leap[®] Chlorine Infuzer[®] and test the water daily until the reading is down to 1.0 ppm. Then reinsert the FROG Leap[®] Torpedo Pac[®], lower the dial one setting and test the water again in 24 hours. If the reading has risen, lower the dial one setting again. Continue this process until proper reading is achieved.
S
Sara BaileySep 4, 2025
Why is my FROG Leap Lighting Equipment over-chlorinating?
- C
  cnguyenSep 4, 2025
  If your FROG Leap Lighting Equipment is over-chlorinating even at the lowest setting, it might be because you are circulating the water more than necessary, depending on your pump size. Consider decreasing the circulation time.
V
vhuynhSep 8, 2025
Where is the pressure relief valve on FROG Leap Lighting Equipment?
- K
  Kevin JohnsonSep 8, 2025
  Check the pressure relief valve on your FROG Leap Lighting Equipment. It is a clear plastic piece approximately 1” long installed inside near the base. If it is loose or missing, replace it, as it can provide another avenue for water to reach the chlorine.