Remote Command Format
All commands with sclr allow either Scaler [A] or Scaler [B] to be selected. If this parameter is not used, Scaler A is
used as the default. Inquiry commands will accept the scaler as an optional parameter. The default is to return
information for Scaler A. Additionally, the sclr parameter will accept [M]ain or [P]review as valid operands.
ACFG sclr Auto Input Configuration (1:1 Sampling): sclr[A|B|P|M]
ADBG d Audio debug: d[0|1]
ADLY d Audio delay adjustment: t[0..50]
AMTE M L P m l p Audio mute control: MLPmlp[0|1] (mute=0),
AOIWN n n n n sclr Area of Interest Window:
Right Edge, HWidth, Bottom Edge, VHeight,
AOUT P p h Audio output control: Pph[0|1]
ARST u Audio reset control: u[0|1]
ARTE a b Audio route: ab[0..7]
ARTEM c Audio route main: c[0..8] where 8 is silent
ARTEP c Audio route preview: c[0..8] where 8 is silent
ASEN p m l s Audio sensitivity: pl[0|1] m[1..3] s[0..15]
ASTAT Audio status: return current status as a sequence of bytes
ASTAV Audio volume status: return current volume status as a
sequence of bytes
ATRM c v Audio source trim: c[1..8] v[0..51]
ATRN t c Audio transition: t[0..5000] c[0..5000]
AVOL t i r Audio volume: t[1..8] i[-1,1] r[10,25,40]
AVS t m Set audio video mode t[0,1] 0:integration 1:presentation
m[1…3] 1: Video 2: Audio 3: Both
CHKSUM Returns the list of flash-stored file checksums
CMDST? Last Command Status Inquiry,
COMCK op Communication Check:
op[D|U] DOWNLOAD|UPLOAD 128 bytes
DEBUG? Debug Inquiry
DL op nn sclr Download CFG: op[I|P] nn[0-64] sclr[A|B|P|M]
ECHO port n Echo Enable/Disable:
port[A|B] COM_A|COM_B n[0|1] DIS|ENA
FREEZ n sclr Freeze: n[0|1] OFF|ON sclr[A|B|P|M]
FSB n sclr Force Scaler Black: n[0|1] OFF|ON sclr[A|B|P|M]
HELP I Help Command: i[A-Z], Help Index
IBRT op nnn sclr Input Brightness:
op[C|R|G|B] (C)n[75 - 125]% (RGB)n[-25 - 25]%
ICDEL nn Input Configuration Delete: n[1-64]
ICFGN nn Input Configuration File Name: n[1-64]
ICGTE n sclr Input Clamp Gate: n[0-2], SYNC|PRCH|PDLY sclr[A|B|P|M]
ICNT op nnn sclr Input Contrast: op[C|R|G|B] (C)n[75 - 125]% (RGB)
n[-25 - 25]%
ICPH op sclr nn Input Clock Phase: op[A|D|M|I], sclr[A|B|P|M], n[0-31]
ICPHO op sclr nn Input Clock Phase Offset:
op[A|D|M|I], sclr[A|B|P|M], n[-16 to 16]
ICPL op sclr nnnn Input Clocks Per Line: op[A|D|M|I], sclr[A|B|P|M], n[0-4096]
ICREC nn sclr Input Configuration Recall: n[1-64] sclr[A|B|P|M]
ICRST sclr Input Configuration Reset: sclr[A|B|P|M]
ICSAV nn s[8] sclr Input Configuration Save: n[1-64] s[Name] sclr[A|B|P|M]
ICSP n sclr Input Colorspace: n[0-6], RGB|B50|B60|MII|EBU|NTSC|SVID
IHRE sclr? Input Right Edge Inquiry: sclr[A|B|P|M]
IHUE nnn sclr Input Hue: n[0-360 degrees] sclr[A|B|P|M]
IHW sclr? Input Left Width Inquiry: sclr[A|B|P|M]
IRSP op nnn sclr Input Raster Size/Position:
op[L|R|T|B] nnn[-999 - 999] sclr[A|B|P|M]
ISAT nnn sclr Input Saturation: n[50-200]% sclr[A|B|P|M]
ISYNC n sclr Input Sync: n[0-3], SOG|CSYN|H&V|AUTO sclr[A|B|P|M]
KEY c sclr n Luma Keying n[ ‘X’ | ’K’ | ’W’ ] OFF|KEY|WINDOWING
Compass S
2
35
To Next Page
Loading...