Why Fujitsu Tablet PC does not turn on in Port Replicator?
If your Fujitsu Tablet PC does not turn on when installed in the optional Port Replicator, ensure the Port Replicator AC adapter is plugged in to provide power. Also, verify that the Tablet PC is properly seated in the Port Replicator by removing and re-docking it.
Why my Fujitsu Tablet PC won't work on battery?
If your Fujitsu Tablet PC will not work on battery alone, replace the battery with a charged one or install a power adapter. If no battery is installed, install a charged battery. If the battery is improperly installed, verify that the battery is properly connected by re-installing it.
What causes bright or dark spots on Fujitsu LIFEBOOK T730 Laptop display?
If the display of your Fujitsu Laptop has bright or dark spots that interfere with your operation needs, the display is faulty and you should contact your support representative.
Why is the battery indicator not illuminating on my Fujitsu LIFEBOOK T730?
If your Fujitsu laptop's battery indicator isn't lighting up, the issue might stem from incorrect battery installation or a fully discharged battery. First, power off your laptop and ensure the battery is correctly installed in its compartment. Then, switch the laptop back on. If the indicator still doesn't illuminate, try charging the battery, installing a charged battery, or connecting your laptop to a power outlet using the mains adapter.
Why Fujitsu LIFEBOOK T730 Laptop cannot be started?
If your Fujitsu laptop cannot be started, there might be a few reasons: the battery might not be installed correctly, the battery might be dead, or the power adapter might not be connected properly. First, check whether the battery is correctly installed in its compartment. If it is, try charging the battery, inserting a charged battery, or connecting the mains adapter to the notebook. Also, check whether the mains adapter is properly connected to the notebook.
Why does the battery discharge too quickly on my Fujitsu LIFEBOOK T730 Laptop?
If the battery on your Fujitsu laptop discharges too quickly, it may be because the battery is either too hot or too cold. Allow the notebook to return to a normal temperature. If the operating time is still extremely short, the battery is likely too old and should be replaced. Additionally, an application might be consuming excessive power. Use the mains adapter as frequently as possible. Finally, the screen brightness might be set too high, so decrease it using the key combination for screen brightness.
Why the radio connection to a network does not work on Fujitsu LIFEBOOK T730?
If the radio connection to a network does not work on your Fujitsu laptop, the wireless component may be disabled. Switch the radio component on. If the wireless component is enabled but the connection still doesn't work, check whether the radio connection is switched on via the software. Further information on using the radio component can be found in the help files.
Why does my Fujitsu LIFEBOOK T730 Laptop type numerals instead of letters?
If certain characters are entered on the keyboard of your Fujitsu laptop and only numerals are written, the virtual numeric keypad of your device is activated. Press the Num key to deactivate it.
What to do if my Fujitsu LIFEBOOK T730 doesn't recognize DVD/CD-RW/CD-ROM?
If your Fujitsu Laptop fails to recognize a DVD/CD-RW/CD-ROM, first ensure the disc is correctly installed on the raised center circle of the drive. Then, verify that you have DVD Player software installed. Also, ensure the optical drive tray is latched shut. If issues persist, verify the drive designator used by the application matches the one used by the operating system. Finally, inspect the DVD/CD-RW/CD-ROM for dirt or defects; wipe it with a non-abrasive CD cleaning cloth or try another disc.
What to do if Fujitsu LIFEBOOK T730 Laptop won't load operating system?
If your Fujitsu system powers up and displays power on information but fails to load the operating system, ensure you have the correct password if you have a secured system. Also, verify the Security settings. If that's not the case, set the operating source by pressing the [ESC] key or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. Finally, use the BIOS setup utility to try to auto detect the internal hard drive.
To Next Page
General