13 EN
• When all the Timer Recordings are completed, the also
flashes. To play or eject the recorded tape, press
FUNCTION
first
, and then press PLAY/K or EJECT. To rewind the tape
to the beginning of the recorded programmes, press
AUTO RETURN on the VCR.
• The TV that is connected to your VCR may be turned on
or off when the VCR is in the Timer-recording mode.
• The VCR will only perform a timer recording after it has
been placed into timer standby mode.
Auto Return
Using the AUTO RETURN Button
When all the Timer Recordings are completed (the
indicator flashes), press
AUTO RETURN on the VCR first. The
VCR will rewind to the beginning of the recorded
programme(s).
Note: If there are any remaining programmes, press
FUNCTION to turn on the VCR and then press
AUTO RETURN. In this case, if you press any other
button once and then press
AUTO RETURN, AUTO
RETURN will not be carried out.
Using the VCR Menu
If there are any remaining programmes including Daily,
Everyday, & Weekly, AUTO RETURN will not operate.
1) Press MENU.
2) Press
PLAY/K or STOP/L repeatedly to point to “SET
UP”, then press
F.FW D /B.
3) Press
PLAY/K or STOP/L to point to “AUTO
RETURN”, then press
F.FW D /B.
[ON] will appear next to “AUTO RETURN”.
4) Press MENU.
Watch the Recorded Timer Programme
Press FUNCTION to turn on the VCR, then press PLAY/K.
Parents Lock
Parents Lock prevents use of the VCR by making the VCR
feature buttons on the VCR and the remote control
inoperative.
•The PWR indicator on the display comes on.
1) Press and hold down
FUNCTION on the remote control for
5 seconds until “PL” appears on the display. The Parents
Lock is activated.
When you want to cancel it, press and hold
FUNCTION on
the remote control again for 5 seconds.
When Parents Lock is activated:
• The time will appear on the display. “PL” will appear on
the display for two seconds every minute.
•You may insert a tape. However, the VCR power will
remain off.
• You may press
EJECT to remove the tape (unless a timer
recording is programmed or has finished).
• Timer recording will take place as scheduled, even if
Parents Lock is activated. “P.L.” will appear steadily on the
TV screen during the timer recording.
VPS (Video Programme System)/PDC
(Programme Delivery Control)
Operation only for 29A-654/29A-754 only
The Video Programme System (VPS) or the Programme
Delivery Control (PDC) is a very convenient system which
assures that the TV programmes you have programmed for
timer recording, will be recorded exactly from beginning to
end, even if the actual broadcasting time differs from the
scheduled time due to delayed start or extension of the
programme duration. Also, if a programme is interrupted and,
for example, some special news is broadcast, the recording will
also be interrupted automatically and resumed when the
programme continues.
When the VPS/PDC signal drop out because the broadcast
signal is weak, or when a broadcasting station does not
transmit a regular VPS/PDC signal, the timer recording will be
performed in the normal mode (without VPS/PDC) even if it
was programmed for VPS/PDC. When the starting time of the
VPS/PDC timer recording is from 0:00 to 3:59 on a given day,
the VPS/PDC function operates from 20:00 on the previous
day to 4:00 on the following day. When the starting time of
the VPS/PDC timer recording is from 4:00 to 23:59 on the
given day, the VPS/PDC function operates from 0:00 on the
day to 4:00 on the following day. This means that if the
relevant programme is broadcasted within this period, it will
be recorded correctly. If the timer is not programmed
correctly, the incorrect timer setting stays in effect unless you
cancel it. To cancel the incorrect timer setting, refer to “To
Cancel or Check the Start/End Time’’ on page 12.
QUICK-FIND
This function enables you to search and confirm the contents
of the recorded programme(s) using the index mark.
• Use the remote control for this procedure.
• The tape must be fully rewound.
1) Press
QUICK-FIND.
To Skip to the Beginning of Next Programme
1) Press QUICK-FIND.
To View at Normal Speed
1) Press PLAY/K. The Quick-Find is cancelled.
Note: • This function will not operate in the Recording mode.
• When you want to cancel the Quick-Find while in
progress, press STOP/L.
• When the end of a tape is reached during the Quick-
Find, the tape will automatically rewind to the
beginning. After rewinding finishes, the VCR will
eject the tape and turn itself off.
INDEX SEARCH
• The index mark will be made automatically when
REC/OTR is pressed. It will also be marked at the starting
point of Timer recording and OTR.
• The index mark is not recorded if
PAUSE/STILL is pressed
and released during recording.
• The time gap between index marks on the tape should be
greater than 1 minute for SP recording and 2 minutes for
LP recording.
• Use the remote control for this procedure.
1) Press SEARCH MODE.
2) Press
PLAY/K or STOP/L repeatedly until the number of
programmes that you want to skip appears.
3) Press
REW/s or F. F WD/B.
The VCR begins rewinding or fast forwarding to the
beginning of desired programme.
When the preset programme is reached, the VCR will start
playback automatically.
Note: • Index Search can be set up to 20.
• This function will not operate in the Recording mode.
29A-650(EN).fm Page 13 Wednesday, October 27, 2004 10:40 AM
To Next Page
Loading...
