FUNAI 29A-650 - Page 8

8 EN
6) Press the number buttons, PLAY/K, or STOP/L to select
your desired position number, then press
F.FW D /B.
•You can select position number 01-99.
•If [ON] appears on the right side of “SKIP”, press
PLAY/K or STOP/L to point to “SKIP”. Then, press
F.FW D /B to select [OFF].
•If you want to remove scrambled signals, press
PLAY/K or STOP/L repeatedly to point to
“DECODER”. Then, press
F.FW D /B to select [ON].
7) Press
PLAY/K or STOP/L to select “CHANNEL”, then
press
F.FW D /B.
Press
PLAY/K or STOP/L. The VCR tuner will begin to
search up or down automatically. When a channel is
found, the VCR will stop searching and the picture will
appear on the TV Screen.
•You can select desired channel number by using
the
number buttons. You must refer to the following
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press “
0” button first and then
press “
2” and “4”.)
•If this is the channel you want, press
F.FW D /B.
This VCR can receive Hyper and Oscar frequency bands.
8) Press
MENU to exit.
Note: To confirm that a channel has been added, press
CHANNEL (K/L).
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels by pressing
CHANNEL (K/L).
• Use the remote control for this procedure.
1) Press
MENU.
2) Press
PLAY/K or STOP/L to select “INITIAL”, then press
F.F WD /B.
3) Press
PLAY/K or STOP/L to select “CH TUNING”, then
press
F.FW D /B.
4) Press PLAY/K or STOP/L to select “MANUAL”, then
press
F.F WD /B.
5) Press
PLAY/K or STOP/L to select “POSITION”, then
press
F.F WD /B.
6) Press the
number buttons, PLAY/K, or STOP/L to select
relevant position number, then press
F.F WD /B.
7) Press
PLAY/K or STOP/L to select “SKIP”, then press
F.FW D /B to select [ON].
•To memorize the channel again, press
F.FW D /B. “ON”
will change to “OFF”.
Note for 29A-654 and 29A-754 only
•The VCR refers to the PDC channel which was
memorized into position 01 when you set the Auto
Clock.
The position 01 must therefore be set “SKIP” to [OFF].
8) Press
MENU to exit.
Note: To confirm that a channel has been deleted, press
CHANNEL (K/L).
Channel Reprogramming
You can replace two channels.
• Use the remote control for this procedure.
1) Press
MENU.
2) Press
PLAY/K or STOP/L to select “INITIAL”, then press
F.FW D /B.
3) Press
PLAY/K or STOP/L to select “CH TUNING”, then
press
F.F WD /B.
4) Press
PLAY/K or STOP/L repeatedly to select “MOVE”,
then press
F.FW D /B.
5) Press
PLAY/K or STOP/L repeatedly to select the position
number you want to change the channel, then press
F.FW D /B.
•You cannot select a position number where “- - -”
appears next to the number. This is because SKIP is set
to [ON] for this position number.
•When a weak signal is received in Channel
Reprogramming mode, you can change the background
to solid blue by pressing
TAPE COUNTER RESET.
If you press the button again, the background will return
to the static screen.
6) Press
PLAY/K or STOP/L repeatedly until the channel
move to another position number, then press
F.FW D /B.
Channel Plan
CH Indication TV Channel
02 – 12 E2 – E12
13 – 20 A – H (only ITALY)
21 – 69 E21 – E69
74 – 78 X, Y, Z, Z+1, Z+2
80 – 99,100 S1 – S20,GAP
121 – 141 S21 – S41
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[OFF]
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[ON]
CH TUNING
AUTO
MANUAL
MOVE
MENU
TIMER
SET UP
INITIAL
29A-650(EN).fm Page 8 Wednesday, October 27, 2004 10:40 AM