FUTABA T26SZ - Page 176

176
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŶƈƗƗƌƑƊŃƐƈƗƋƒƇƖ
ŏ*URXSVLQJOHPRGHVHOHFWLRQ
Activating functions for only the selected
conditions:
1. Tap the [Gr] button and switch to the [Sngl ] mode.
*Each time the button is tapped, it toggles between the Gr
and Sngl modes.
ŏ0L[LQJPRGHVHOHFWLRQ
Using the offset mode:
1. Tap the Mode button and switch to the Offset
mode.
*Each time the button is tapped, it toggles between the
0L[LQJDQG2൵VHWPRGHV
ŏ0L[LQJVHWXSVFUHHQVHOHFWLRQ
1. Tap the button of the mixing you want to set. The
mixing setup screen is displayed. Activate the
function.
2. Activate the function by tapping the [INH] button.
*Each time this button is tapped, it toggles between [INH]
and [ON/OFF].
ŏ0L[LQJ212))VZLWFKVHWWLQJDQG212))GLUHFWLRQ
switching
*An ON/OFF switch is not set even when the function is
activated.
1. When you want to turn mixing ON/OFF by switch,
tap the [--] button to call the <Switch> screen and
then select the switch and its ON direction.
*For a description of the selection method, see [Switch
setting method] at the back of this manual.
ŏ0DVWHUFKDQQHOVHWWLQJH[FHSWRIIVHWW\SHPL[LQJ
1. Tap the Master button to call the Function menu
and select the master channel.
2. To link this mixing with other mixing, tap the "Link"
button.
*Each time the button is tapped, it toggles between mixing
direction + and - and "OFF" (no link).
*Master channel control can be set to stick, VR, and other
simple travels which do not include End point, AFR, D/R,
mixing setting, etc. In this case, display the <Function,H/
W> screen by tapping the [Stick, Switch, Dial] button and
then select master channel side control.
ŏ6ODYHFKDQQHOVHWWLQJ
1. Tap the Slave button to call the Function menu
and select the slave channel.
2. To link this mixing with other mixing, tap the "Link"
button.
*Each time the button is pressed, it toggles between mixing
direction + and - and "OFF" (no link).
ŏ7ULPPRGH212))VHWWLQJ
1. To turn the trim mode ON/OFF, tap the Trim button
on the screen.
*When mixing includes master side trim, set the Trim button
to [ON]. When mixing does not include master side trim, set
the Trim button to [OFF].
*Each time this button is pressed, it toggles between [ON]
and [OFF].
7KLVLVH൵HFWLYHZKHQWKHPDVWHUFKDQQHOLVVHWE\)XQFWLRQ
ŏ0L[LQJFXUYHW\SHVHOHFWLRQ
1. Tap the curve type selection button of the curve
type you want to use to display the selection
screen. Then, select the curve you want to use.
*For a description of the curve setting method, see the
description at the back of this manual.
ŏ)LQHWXQLQJWULPVHWWLQJ
1. When using the curve fine tuning function, tap
the [--] button of the Fine Tuning item to call the
<Switch> screen and then select the lever, VR, etc.
you want to use.
)RUDGHVFULSWLRQRIWKH¿QHWXQLQJWULPVHWWLQJPHWKRGVHH
the description at the back of this manual.
ŏ6HUYRVSHHGVHWWLQJ
1. When setting the servo speed, tap the speed
button. The Servo speed setup screen is displayed.
*For a description of the servo speed setting method, see the
description at the back of this manual.
*Offset mixing changes the speed. Use the Speed In and
Speed Out buttons to readjust the speed.
The mixing switch can set a delay with a different rate at
starting and stopping.
*This function is inactive when a mixing switch is not set.