FUTABA T26SZ - Page 179

179
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ųƌƗƆƋŃƗƕƌƐŃŋūƒƙƈƕƌƑƊŃƓƌƗƆƋŏŃƋƌƊƋŃƓƌƗƆƋŏŃƏƒƚŃƓƌƗƆƋŌ
The hovering pitch, low pitch, and high pitch trim setup screen can be called from the Pitch curve setup
screen.
Hoveringpitchtrim
setting
Low/highpitchtrim
setting
ūƒƙƈƕƌƑƊŃƓƌƗƆƋŃƗƕƌƐ
The Hovering Pitch trim function trims the pitch
near the hovering point. Normally, it is used with
the hovering condition. The hovering pitch can be
¿QHWXQHGIRUFKDQJHVLQURWRUVSHHGDFFRPSDQ\LQJ
FKDQJHVLQWHPSHUDWXUHKXPLGLW\DQGRWKHUÀLJKW
conditions. Adjust the hovering pitch so that
rotor speed is constant. This function can be used
together with the hovering Throttle Trim function
for more delicate operation.
ŶƈƗƗƌƑƊŃƐƈƗƋƒƇ
ŏ:KHQXVLQJRQO\WKHKRYHULQJQRUPDOFRQGLWLRQ
switch the group mode to the single mode (initial
setting) before setting.
ŏ7DS>,1+@21LVGLVSOD\HG
ŏ6HOHFWWKHDGMXVWPHQWNQRE
Selection example: LD
ŏ7KHWULPRSHUDWLRQPRGH0RGH&HQWHU1RUPDO
can be selected.
Center mode: Maximum amount of change near
center by center trim operation (recommended)
Normal mode: Normal trim (parallel movement
trim) operation. The advantage of using this mode
is that the hovering pitch can be adjusted without
changing the curve.
ŏ7ULPDGMXVWPHQWUDQJH5DQJHVHWWLQJ
When this value is made small, trim can only be
used near the center.
ŏ7KHWULPUDWHFDQEHDGMXVWHGDQGWKHRSHUDWLRQ
direction can be changed.
ūƌƊƋŃųƌƗƆƋŒůƒƚŃųƌƗƆƋŃŷƕƌƐ
High Pitch/Low Pitch Trim is the pitch servo high
side and low side trim function.
ŶƈƗƗƌƑƊŃƐƈƗƋƒƇ
ŏ:KHQVHWWLQJWKHDGMXVWPHQWNQREVFRPPRQWRDOO
the conditions, set them in the group mode.
ŏ7DS>,1+@21LVGLVSOD\HG
ŏ6HOHFWWKHDGMXVWPHQWNQREV
Selection example: LS (high side), RS (low side)
ŏ7KHWULPUDWHFDQEHDGMXVWHGDQGWKHRSHUDWLRQ
direction can be changed.
ŏ7ULPDFWVDVKLJKVLGHRUORZVLGHWULPZLWKWKH
center as the standard.
ŏ5HWXUQWR0RGHOPHQX