FUTABA T26SZ - Page 187

187
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ųƌƗƆƋ ڀ ŵƘƇƇƈƕŃŃŋŵƈƙƒƏƘƗƌƒƑŃƐƌƛƌƑƊŌ
Use this mix when you want to suppress the
reaction torque generated by main rotor pitch and
speed changes during pitch operation. Adjust so
that the nose does not move in the rudder direction.
An acceleration function which temporarily
increases the correction rate at throttle stick
acceleration/deceleration operation can be set. The
mixing rate at acceleration/deceleration can be set.
ŶƈƗƗƌƑƊŃƐƈƗƋƒƇ
ŏ:KHQXVLQJWKLVIXQFWLRQ7DS>,1+@21LV
displayed.)
ŏ:KHQ\RXZDQWWRVHWWKHVDPHFRQWHQWVDWRWKHU
conditions, select the group mode.
When you want to set the selected condition only,
select the single mode (initial setting).
ŏ$PL[LQJFXUYHLVVHW
1RUPDOFRQGLWLRQPL[LQJFXUYH!
The mixing curve rate starts from a small
value.
For a rotor with a clockwise operation
direction (polarity), when pitch was
operated at the plus side, set so that
mixing is in the clockwise direction. First,
trim at hovering and then adjust the
neutral position.
1. Adjustment between slow and hovering
Repeatedly hover from take off and land
from hovering at a constant rate matched
to your own rhythm, and adjust the pitch
VRWKHQRVHGRHVQRWGHÁHFWZKHQWKH
throttle is raised and lowered.
2. Throttle high side (climbing and diving
from hovering)
Repeat climbing and diving from hovering at
a constant rate matched to your own rhythm
and adjust the pitch so that the nose does not
GHÁHFWZKHQWKHWKURWWOHLVUDLVHGDQGORZHUHG
However, when a GY Series or other heading hold
gyro is used, since correction is performed by the
gyro, this mix is not used. If this function is used
when the gyro operation mode is the AVCS mode,
the neutral position will change.
,GOHXSFRQGLWLRQPL[LQJFXUYH!
Set the mixing rate so that the rudder
GLUHFWLRQDWKLJKVSHHGÁLJKWLVVWUDLJKW
ahead. Adjust for each condition used.
$FFHOHUDWLRQIXQFWLRQVHWWLQJ!
ŏ$FFHOHUDWLRQRSHUDWLRQFDQEH
performed for both setting at acceleration
(High) and setting at deceleration (Low).
ŏ$FFHOHUDWLRQUDWHVHWWLQJ5DWH
ŏ7KHUHWXUQWLPHDIWHURSHUDWLRQ'DPSLQJ
can be set.
ŏ$QRSHUDWLRQSRLQW$FWSRVLWLRQDW
acceleration and deceleration can be set
independently. When an operation point
was exceeded, acceleration operation is
performed.
ŏ6HOHFW>3LWFKń5XGGHU@DW
the model menu and call
the setup screen shown.
●Mixingcurvesetting
*Foradescriptionofthe
curvesettingmethod,
seethedescriptionat
thebackofthismanual.
Normally,use[Point]type.