FUTABA T26SZ - Page 35

35
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŰƒƇƈƏŃŬŧ
ŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃŃ
ũŤŶŶŷƈƖƗŏŃŷŐũūŶŶŃŤŬŵ
For the sake of safety, this function does not operate the receiver if the model data of the model program
settings that does not match the aircraft is used by mistake.
Ŷ,QWKHV\VWHPW\SHV)$667HVW7)+66$,5
compatible with the model ID function, a unique
ID number (model ID) is set to each model data.
Linking with a receiver stores the model ID of the
model data in that receiver. The receiver operates
only when it receives radio waves transmitted using
model data that matches the stored model ID. As a
result, the receiver does not operate even if model
data of an unintended setting is used by mistake,
so it is possible to prevent a malfunction due to a
model selection mistake.
Ŷ,I\RXZDQWWRXVHGLIIHUHQWPRGHOGDWDIURPWKH
model data that you have been using, link again.
Ŷ0RGHO,'IHDWXUHLVHQDEOHGRQO\LIWKHV\VWHPW\SH
is FASSTest or T-FHSS AIR. Please note that model
ID function can not be used on other systems.
ŃůƌƑƎŃƌƖŃƕƈƔƘƌƕƈƇŃƚƋƈƑŃƄŃƑƈƚŃƐƒƇƈƏŃƌƖŃƐƄƇƈŃƉƕƒƐŃƄŃƐƒƇƈƏŃƖƈƏƈƆƗƌƒƑőŃ
Model1Receiver
Addnewmodeldata
Link
SelectamodelinModelSelect.Linkwithareceiverthatmatchesthemodel.
Link
Link
Model2Receiver
Model3Receiver
1:
3:
Model1
Model2
Model3
2:
1:
3:
Model1
Model2
Model3
2:
1:
3:
Model1
Model2
Model3
2:
Rx1
Rx2
Rx3
SelectModel2
Itworkswithdifferentmodeldata.
Thereisariskofflyingwithdifferentmodeldata!
SelectModel2
Model2onlyworkswithModel2data.
Thereisnoriskofflyingwithdifferentmodeldata.
Conventionalsystem
ModelID
Operation
Operation
Rx1
Rx2
Rx3
Operation
Operation
NotOperation
NotOperation
Ŷ)RUVDIHW\UHDVRQVPRGHO,'IXQFWLRQFDQQRWEH
disabled.
Ŷ0RGHOGDWDWKDWFDQEHVWRUHGLQLQWHUQDOPHPRU\LV
up to 250 models.
Ŷ0RGHO,'LVDXWRPDWLFDOO\VHWZKHQFRS\LQJRU
adding model data.
Ŷ56%UHFHLYHUGRHVQRWVXSSRUWPRGHO,'
function. When using the R3004SB, set “Receiver”
in the system type screen T-FHSS AIR mode setting
to [R3004SB]. When using other T-FHSS AIR
compatible receivers, set "Receiver" to [Normal].