FUTABA T26SZ - Page 45

45
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ŧƌƖƓƏƄƜ
The following LCD screen adjustments:
●
Backlighting brightness adjustment
●
Backlighting decrease time adjustment
●
Touch screen calibration
●
Sub display contrast adjustment
●
Tap the [Display] button in the System menu to
call the setup screen shown below.
●
Return to System menu
ťƄƆƎƏƌƊƋƗŃƐƄƛőŃƅƕƌƊƋƗƑƈƖƖŃƄƇƍƘƖƗƐƈƑƗ
1. Adjust the backlighting brightness with the value
input buttons.
:KHQWKHŸEXWWRQLVWDSSHGWKHEDFNOLJKWLQJEHFRPHV
EULJKWHU:KHQWKHźEXWWRQLVWDSSHGWKHEDFNOLJKWLQJ
becomes darker.
ťƄƆƎƏƌƊƋƗŃƐƌƑőŃƅƕƌƊƋƗƑƈƖƖŃƄƇƍƘƖƗƐƈƑƗ
1. Adjust the backlight decrease brightness with the
value input buttons.
:KHQWKHŸEXWWRQLVWDSSHGWKHEDFNOLJKWLQJEHFRPHV
EULJKWHU:KHQWKHźEXWWRQLVWDSSHGWKHEDFNOLJKWLQJ
becomes darker.
*It cannot be made brighter than Backlighting brightness
adjustment.
ťƄƆƎƏƌƊƋƗŃƇƈƆƕƈƄƖƈŃƗƌƐƈ
1. You can set a time period to decrease the LCD
backlight. This function counts the period that the
Touch Panel has been not operated. This time can
be set by ten-second steps. You can also turn off
the backlight decrease* if you like.
*The backlight consumes a large amount of power. We
recommend that you turn off the backlight by setting the
EDFNOLJKWSRZHUR൵WLPHWRDERXWRQHPLQXWH
ŶƘƅŃƇƌƖƓƏƄƜŃƆƒƑƗƕƄƖƗŃƄƇƍƘƖƗƐƈƑƗ
1. Adjust the sub display contrast adjustment with the
value input buttons.
:KHQWKHŸEXWWRQLVWDSSHGWKHVXEGLVSOD\EHFRPHV
LQFUHDVHFRQWUDVW:KHQWKHźEXWWRQLVWDSSHGEHFRPHV
decrease contrast.
ŷƒƘƆƋŃƆƄƏƌƅƕƄƗƌƒƑŃ
This function adjusts the location of the Touch Panel.
Press the "Touch calibration" button. The calibration
screen will then pop up. Tap the center of the cross
hair cursor on the screen with the soft pen. As soon
as the system recognizes the position, the cursor will
move on to the next position. Repeat this procedure
as long as the cursor moves to next position. You
ZLOOGRWKLVÀYHWLPHV&DOLEUDWLRQZLOOEHFDUULHGRXW
EDVHGRQWKHÀYHSRVLWLRQV'LVDSSHDUDQFHRIWKH
cross hair cursor means the calibration has been
completed.
*In ordinary operation, this calibration is not necessary. If
you notice the Touch Panel is not functioning correctly after
long use, we recommend that you carry out this calibration.