FUTABA T26SZ - Page 71

71
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
●
Tap the [Fail safe] button in the Linkage menu to call the setup screen shown below.
ũƄƌƏŃƖƄƉƈ
Sets the servos' operating position when transmitter signals can no
longer be received or when the receiver battery voltage drops.
The Fail safe function is used to set up positions
that the servos will move to in the case of radio
LQWHUIHUHQFH'H¿QHVVHUYRSRVLWLRQZKHQVLJQDOVDUH
lost and when receiver battery voltage becomes low.
You may set either of two positions for each channel:
Hold, where the servo maintains its last commanded
position, or fail safe, where each servo moves to
a predetermined position. You may choose either
mode for each channel.
The T26SZ system also provides you with an
advanced battery monitoring function that warns
you when the receiver battery has only a little
power remaining. In this case, each servo is moved
WRWKHGH¿QHGIDLOVDIHSRVLWLRQ7KHEDWWHU\IDLOVDIH
PD\EHUHOHDVHGE\RSHUDWLQJDSUHGH¿QHGFRQWURO
on the transmitter (default is throttle). Do not
FRQWLQXHWRÀ\/DQGDVVRRQDVSRVVLEOH5HPHPEHU
if the predefined control suddenly moves to a
ũƄƌƏŃƖƄƉƈŃƖƈƗƗƌƑƊŃƓƕƒƆƈƇƘƕƈ
Decide which channels you want to go to preset
positions, and which ones you want to maintain
their last commanded position. To select the fail
safe mode you wish to set, use the F/S button. This
button toggles between the two modes. (Hold, F/S)
)6PRGHVHWWLQJ
1. Tap the F/S button of the channel you want to set,
and set that channel to the [F/S] mode.
2. Hold the corresponding stick, control, slider, or
other control in the position you want the servo to
move to when the fail safe function is activated,
and tap the F/S position button. That position is
displayed in percentage.
*When you want to return that channel to the Hold mode, tap
the [F/S] button again.
ťƄƗƗƈƕƜŃƉƄƌƏŃƖƄƉƈŃƖƈƗƗƌƑƊŃƓƕƒƆƈƇƘƕƈ
To select the B.F/S mode, tap the [B.F/S] button.
Each time the button is tapped, it toggles between
[OFF] and [B.F/S].
%)6VHWWLQJ
1. Tap the [B.F/S] button of the desired channel to set
it to the B.F/S mode.
position you did not command, land at once and
check your receiver battery.
Do not continue to fly. Land as soon as possible.
Defines servo position when signals are lost and
when receiver battery voltage becomes low.
WARNING

Forsafety,alwayssetthefailsafefunctions.
Ŷ(VSHFLDOO\VHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDWWKH
servo moves to the maximum slow side for airplanes and to the
slow side from the hovering position for helicopters. Crashing
of the model at full high when normal radio waves cannot be
received due to interference, etc., is very dangerous.
Ŷ,IIDLOVDIHLVUHVHWE\WKURWWOHVWLFNPRYHPHQWWKHIDLOVDIH
may be mistaken as an engine malfunction and will be reset
DWORZWKURWWOHDQGWKHPRGHOZLOOFRQWLQXHWRÀ\,I\RXKDYH
any doubts, immediately land.
2. Hold the corresponding stick, VR, slider, or other
control in the position you want the servo to move
to when the battery fail safe function is activated,
and tap the F/S position button. This position is
displayed in percentage.
*When you want to return that channel to OFF, tap the [B.F/S]
button again.
ťƄƗƗƈƕƜŃũƄƌƏŃƖƄƉƈŃƕƈƏƈƄƖƈŃƉƘƑƆƗƌƒƑ
7KLVIXQFWLRQUHOHDVHVWKHSUHGH¿QHGFRQWUROIURP
its held position after indicating that your receiver
battery is low.
1. Enter the control setting screen by tapping the
Battery F/S release button. Now, you may choose
whether moving the throttle resets the condition,
or select a stick or switch to deactivate it. To set a
desired throttle release position, move the throttle
stick to the point at which you wish the B.F/S to be
released.
●
Return to Linkage
menu