FUTABA T26SZ - Page 95

95
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
Altitude
Setsthealtitude
onwhichthealarm
operates.
↑ Anupwardarrow
indicatesthealarmwill
soundwhenthealtitude
reachesaboveyourset
value.
↓ Adownwardarrow
indicatesthealarmwill
soundwhenthealtitude
reachesbelowyourset
value.
Alarmischosenfrom
Buzzer,Voice,and
Inhibit.
AllowsSpeechtobe
turnedONorOFF.
AllowsMelodytobe
turnedONorOFF.
●
Tap the [Altitude] button in the Telemetry screen to call
the setup screen shown below.
Max.andmin.values
sincethepowerwas
turnedONwilldisplay.
Type1
Type2
Type3
"Vibrator"type
Ifthefollowingtypesareselected,thetransmitter
willvibrateduringthewarning.
ŷƈƏƈƐƈƗƕƜŃŝŃŤƏƗƌƗƘƇƈ
Displaying data from the altitude
Altitude is a screen which displays / sets up the altitude
information from an optional altitude sensor or GPS sensor.
7KHDOWLWXGHRIWKHPRGHOZKLFKLVÀ\LQJFDQEHNQRZQ,ILW
becomes higher (low) than preset altitude, you can be told by
alarm. Warning by vibration can also be chosen. Data when
a power supply is turned on shall be 0 m, and it displays the
altitude which changed from there. Even if the altitude of an
DLU¿HOGLVKLJKWKDWVKDOOEHPDQGWKHDOWLWXGHGL൵HUHQFH
from an airfield is displayed. This sensor calculates the
altitude from atmospheric pressure. Atmospheric pressure
will get lower as you go up in altitude. Using this, the
sensor will estimate the altitude. Please understand that an
exact advanced display cannot be performed if atmospheric
pressure changes in a weather situation.
ũƌƕƖƗŏŃƗƋƈŃƖƈƗŃƒƉŃƄŃƕƈƉƈƕƈƑƆƈŃƌƖŃƕƈƔƘƌƕƈƇő
1. The model and transmitter to which the altitude
sensor was connected are turned on.
2. Tap to the [Preset] of "Reference" item.
*Atmospheric pressure is changed according to the weather
DOVRDWWKHVDPHDLU¿HOG<RXVKRXOGSUHVHWEHIRUHDÀLJKW
ŤƏƄƕƐŃƖƈƗŃŝŃŤƏƗƌƗƘƇƈŃ
1. Tap Alarm and choose from Buzzer, Voice, and
Inhibit.
2. Choose "Inhibit" for Vibrator if not using the vibrator
alarm. If using vibrator, choose one of the three
types.
3. Tap to the Limit [xxx
m
] item.
4. Adjust the rate using the
"▼▼""▼""▲""▲▲"
buttons.
 ,QLWLDOYDOXHŃPŅP
 $GMXVWPHQWUDQJHPaP
Ń/LPLW
≧
Ņ/LPLW
*When the screen is tapped for one second, the rate is reset
to the initial value.
5. To terminate the input and return to the original
state, push the EXIT button.
*AnaltitudesensororGPSsensormustbeinstalledintheaircraft.
● IfthisissettoMode1-4,a
riseanddivearetoldbya
differentmelody.
Mode1:Littlerise/dive
→ Melodychanges
:sensitively
Mode4:Bigrise/dive
→ Melodychanges
:insensible
●
Return to Linkage
menu