FUTABA T26SZ - Page 96

96
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
Variometer
Setsthevariometer
onwhichthealarm
operates.
↑ Anupwardarrow
indicatesthealarm
willsoundwhenthe
variometerreaches
aboveyoursetvalue.
↓ Adownwardarrow
indicatesthealarm
willsoundwhenthe
variometerreaches
belowyoursetvalue.
Alarmischosenfrom
Buzzer,Voice,and
Inhibit.
AllowsSpeechtobe
turnedONorOFF.
AllowsMelodytobe
turnedONorOFF.
●
Tap the [Variometer] button in the Telemetry screen to
call the setup screen shown below.
Max.andmin.values
sincethepowerwas
turnedONwilldisplay.
Type1
Type2
Type3
"Vibrator"type
Ifthefollowingtypesareselected,thetransmitter
willvibrateduringthewarning.
ũƌƕƖƗŏŃƗƋƈŃƖƈƗŃƒƉŃƄŃƕƈƉƈƕƈƑƆƈŃƌƖŃƕƈƔƘƌƕƈƇő
1. The model and transmitter to which the altitude
sensor was connected are turned on.
2. Tap to the [Preset] of "Reference" item.
*Atmospheric pressure is changed according to the weather
DOVRDWWKHVDPHDLU¿HOG<RXVKRXOGSUHVHWEHIRUHDÀLJKW
*AnaltitudesensororGPSsensormustbeinstalledintheaircraft.
ŷƈƏƈƐƈƗƕƜŃŝŃŤƏƗƌƗƘƇƈŃžŹƄƕƌƒƐƈƗƈƕƀ
Displaying data from the
variometer
VARIO is a screen which displays / sets up the
variometer information from an optional altitude
sensor or GPS sensor.
7KHYDULRPHWHURIWKHPRGHOZKLFKLVÀ\LQJFDQEH
known.
If it becomes higher or lower than the setting, an
alarm and/or vibration will alert you.
To ensure that the pilot is aware as to the model's
VWDWXVWKH76=LQFRUSRUDWHVDGL൵HUHQWPHORG\
for ascent and descent. Additionally, depending
upon the rate of climb or descent, the tones vary to
indicate whether or not the airplane is climbing or
descending at a rapid rate.
ŤƏƈƕƗŃƖƈƗŃŝŃƙƄƕƌƒƐƈƗƈƕŃ
1. Tap Alarm and choose from Buzzer, Voice, and
Inhibit.
2. Choose "Inhibit" for Vibrator if not using the vibrator
alarm. If using vibrator, choose one of the three
types.
3. Tap to the Limit [m/s] item.
4. Adjust the rate using the
"▼▼""▼""▲""▲▲"
buttons.
 ,QLWLDOYDOXHP
 $GMXVWPHQWUDQJHPVaPV
Ń/LPLW
≧
Ņ/LPLW
*When the screen is tapped for one second, the rate is reset
to the initial value.
5. To terminate the input and return to the original
state, push the EXIT button.
● IfthisissettoMode1-4,a
riseanddivearetoldbya
differentmelody.
Mode1:Littlerise/dive
→ Melodychanges
:sensitively
Mode4:Bigrise/dive
→ Melodychanges
:insensible
●
Return to Linkage
menu