FUTABA T32MZ

83
＜
Linkage Menu
＞
+(/,&237(5
$,53/$1(*/,'(5
6\VWHP7\SHVHOHFWLRQ
7KH70=LVIRU*+]RQO\7KHV\VWHPFDQEH
changed from among 5 choices: FASSTest 18CH,
FASSTest 12CH, FASST MULTI, FASST 7CH,
S-FHSS, T-FHSS. Select the system matched to the
type of receiver you are using.u
*Even if it changes a system type, other model data is not
reset.
e
*If a system type is changed in the case of a helicopter, It
can choose out of two channel orders.
[Yes] : Selection sets the channel order suitable for system
type. (We recommend here.)
[No] : The present channel order is maintained.
*All control surfaces should be checked for the correct
operating directions and operating smoothness before
À\LQJWKHPRGHO
$QDORJVHUYRVFDQQRWEHXVHGZLWKWKH56%LQWKH
FASSTest 12CH mode.
5HFHLYHUOLQNLQJ
The receiver will only be controlled (without being
affected by other transmitters) by the transmitter it
is linked to. When using a receiver other than one
purchased as a set, linking is necessary.
Moreover, a re-link is required when a new model
is added by model selection, and the time of system
type change.
'XDOUHFHLYHUIXQFWLRQRQO\)$667HVW&+
PRGH
Dual receivers can be linked with the T32MZ.
Two receivers are recognized individually by ID
QXPEHUV)RUH[DPSOHLQ56%&+RXWSXW
VHWWLQJIXQFWLRQLVXVHGE\VHWWLQJWKH¿UVWDVDV
"1-8CH", and setting the second as "9-16CH",
two sets of receivers can be used as a set in the
ŏ5HWXUQWR/LQNDJH0HQX
ŏ7RXFKWKH>6\VWHP7\SH@EXWWRQLQWKH/LQNDJH0HQX
WRFDOOWKHVHWXSVFUHHQVKRZQEHORZ
6\VWHP7\SH
6\VWHPPRGHVHWWLQJ5HFHLYHUOLQN
model, allowing you 16 channels. If a dual receiver
function is used, the following function can set up
individually.
・
Battery fail-safe voltage setup
A telemetry function cannot be used for the 2nd
receiver.

7KHYROWDJHDQG([WYROWDJHRIDQG
receiver cannot be known with a transmitter.
7HOHPHWU\IXQFWLRQRQO\)$667HVWPRGH
To use the telemetry function, set “Telemetry” to
“ON”.
'/,QWHUYDORQO\)$667HVWPRGH
When a telemetry function is enabled, the receiving
interval (down-link interval) of sensor data can be
changed.
,ID'/LQWHUYDOLVLQFUHDVHGWKHUHVSRQVHRI
the sensor data display becomes slower, but stick
response will improve.
%DWWHU\IDLOVDIHYROWDJHVHWXS)$667HVW
7)+66PRGH
The voltage which battery fail-safe activates, can
EHVHWZKHQ\RXOLQN97KHUHFHLYHU
memorizes the setting as it was at link.
Suggested setting voltages are as follows.
FHOOV1L&GRU1L0+1RUPDO V) = 3.8 V
• 2 cells LiFe (Normal: 6.6 V a V
FHOOV/L3R1RUPDO V a V
It is a rough reference value.
Since it changes with servos carried in the
condition and the model of a battery, please set to
your own model in a battery consumption current.