FUTABA T32MZ

91
＜
Linkage Menu
＞
+(/,&237(5
$,53/$1(*/,'(5
ŏ5HWXUQWR/LQNDJH0HQX
ŏ7RXFKWKH>(QG3RLQW$79@EXWWRQLQWKH/LQNDJH0HQXWR
FDOOWKHVHWXSVFUHHQVKRZQEHORZ
(QG3RLQW$79
6HWVWKHWUDYHOOLPLWSRLQWDQGVSHHGRI
HDFKVHUYR
7KHGLVSOD\VFUHHQLVDQH[DPSOH7KHVFUHHQGHSHQGVRQWKHPRGHOW\SH
The End Point function adjusts the left and right servo
throws, generates differential throws, and will correct
improper linkage settings.
The travel rate

(normal full stick movement at high rates)
FDQEHYDULHGIURPWRLQHDFKGLUHFWLRQRQ
channels 1 to 16. Also, the limit point (how far the servo
WUDYHOVZKHQDPL[LVLQYROYHGZKHUHVHUYRWKURZVWRSV
PD\EHYDULHGIURPWR
6HUYRWUDYHODGMXVWPHQW
7RXFKWKHWUDYHOEXWWRQRIWKHFKDQQHO\RXZDQW
WRVHW$GMXVWPHQWEXWWRQVDSSHDURQWKHVFUHHQ
8VHWKHVHEXWWRQVWRDGMXVWWKHUDWH
ŏ,QLWLDOYDOXH
ŏ$GMXVWPHQWUDQJHa
5HSHDWWKHSURFHGXUHDERYHIRUHDFKUDWH
/LPLWSRLQWDGMXVWPHQW
7RXFKWKHOLPLWEXWWRQRIWKHFKDQQHO\RXZDQWWR
set.
8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHOLPLWSRLQW
ŏ,QLWLDOYDOXH
ŏ$GMXVWPHQWUDQJHa
5HSHDWWKLVSURFHGXUHIRUHDFKOLPLWSRLQW
Note:
The indicators on the screen display actual servo throw
of the each channel. The center position of the indicator is
based on the Sub-Trim settings. Therefore the Sub-Trim
adjustment changes the Limit point display of the indicator.
The Servo Speed setting is used to set the servo delay for
each channel, from channel l to channel 16. The system uses
the programmed speed (delay) to slow down servo position
FKDQJHV7KH6HUYR6SHHGVHWWLQJFDQEHYDULHGIURPWR
in each channel.
6HUYRVSHHGVHWWLQJ
7RXFKWKH6SHHGEXWWRQRIWKHFKDQQHO\RXZDQW
to set.
8VHWKHDGMXVWPHQWEXWWRQVWRDGMXVWWKHVHUYR
VSHHG
ŏ,QLWLDOYDOXH
ŏ$GMXVWPHQWUDQJHaVWHSV
5HSHDWWKLVSURFHGXUHIRUHDFKFKDQQHO
7RFORVHWKLVVFUHHQWRXFKWKH>(QG3RLQW
$79@EXWWRQ
30 〜
140%
30 〜
140%