2.1 Function of FX-RB144
-
Lift sensor
There are lift sensors located between the top and middle
cover. If the mower is lifted from ground, it will stops
working within 1 second.
-
Tilt sensor
There are tilt sensors installed on the mower too, when
the mower is tilted over 30 degrees in any direction, it
stops working within 2 seconds.
- Bump sensor
The whole top cover is movable. Both front and side
of mower equipped with bump sensors that will
activate when the mower strikes solid, fixed object when
that object is at least 6cm in vertical height from the
supporting surface of the mower. When the bump sensor
activated, the mower will back up for working.
- Rain sensor
There are two rain sensors located on the mower.
The mower will go back to the charging station
automatically when it's raining.
Rain sensors can be selected ON/OFF from control panel.
Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.
- Wifi
The IOS user can search “EGROBOT” in the Apple
- Two cutting modes
There are two cutting modes of the mower, go straight
and go circle (high efficiency).
In Auto, mower selects cutting mode intelligently.
It goes straight if the grass is sparse or it has be cut off,
and it goes circle if the grass is dense or long.
In manual mode, the mower will go where you direct it.
Press it to turn off the mower.
- Virtual wire
The robot lawn mower can't be operated without a virtual
wire. (we suggest to use 100m-600m of virtual wire). The
mower will follow virtual wire to charging station, the virtual
wire acts as a virtual fence. It will get on the virtual wire
until it meets charging sheets, then it gets off from virtual
wire and starts cutting inside.
- Mower stops working if virtual wire is cut off or
charging station is power off.
If virtual wire is cut or broken, or the charging station
loosepower, themower will stopworkingwithin 3 seconds
- Five steps to safely start the mower
There are five necessary steps to start the mower:
1.
Connect charging station with power supply by charger
and make sure the recharging light is in green color.
2.
Connect virtual wire to charging station and make sure
it is in good connecting(virtual wire light in colorless).
3.
Turn on the power button and press the emergency
Store to download the application.
button.
4.
Input pa
ssword if selected and selectmode.
The Android user search “EGROBOT” in the Google
Play to download the application.
- Touch sensor
Touch the handle when the mower is cutting, it will
cease function.
- Mowing schedule
Set up one week (From Monday to Sunday, once for
each day) cutting schedule from control panel. This
function should be used together with AREA function.
- Anti-theft function
Mower has password protection option to guard against
theft. What's more, the mower can not be turned on
without a charging station.
- Cutting width: 21cm
- Easy cutting height adjustments
2.5cm-5.5cm selected on LCD display.
- Auto recharge system
When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is
complete, the mower will back up a few centimeters
ready to go again in stand by mode.
- Emergency stop switch
There is an emergency button located on the top of
mower and in red color.
Press it to turn on the mower.
5.
Select working time if needed(10-500mins).
- Overload protect
The brushless cutting motor and each of the two running
motors are monitored continuously during operation for
any situation that may cause these motors to over-load
In the event this is detected, the mower stops operating.
- Waterproof
Waterproof design, there is an inner cover under top
cover which protect inside parts from humidity.
The waterproof class is IP54.
- LCD display
- Gyroscope
The mower has gyroscope to keep it going straight on
inclines.
- Subarea setting
You can select Subareas for the mower to cut. This works
well for large lawn. See Section 5.12.
This function should be used together with schedule.
- Different languages selection.
- Range
There are four range options, user can choose the
distance when robot hit virtual wire according the
condition of different lawns.
- Intelligent cutting height adjustment
There are 7 settings which can be set on display directly.
To Next Page
Loading...
Need help?
General
