Gallo Tech GTS-3RS - Troubleshooting

© Copyright
Gallo Technologies
. All Right Reserved
-
16
-
0
615
1
5
V54RS
attempting to drive the vehicle.
Reconnect the battery and thoroughly test all starting functions.
If the
key
FOBs
a
re not detected by the control module, the
n
re
-
learn both key FOBs
.
S
ee Sec. 1.
6
(A)
for
code
learning instructions
Program the module to the functions that you desire following Sec. 1.
6
“Key FOB &
Program Function Setup”
and
Table 1 “
Function Option Chart
”
.
.
2
.
T
est the starting function
:
a
.
“
Start Stop Engine”
button Starting
:
Press and hold the “
Start Stop Engine
” button without
pressing the brake peddle, making certain that the vehicle will not start. The engine
must
only
start when the brake is pressed an
d the vehicle is in Park or Neutral.
Check to make sure the
vehicle does not start when the gear selector is in Drive or Reverse.
If the engine starts
in Drive or
Reverse
, then the wiring connections
(C3, Pin 14 & 19)
to the Control Module and the connecti
ons
to the Park
/
Neutral switch
(C1 (Orange)
must be rechecked per Figure 1.
b
.
Remote Starting
: Set the Handbrake, move the key FOB out of range (>15 feet) and put the system
in the armed mode (“
Start Stop Engine
” LED flashing
Red
). Press the
2 times. IGN 1 will turn
ON and then the Starter will engage. Once the engine starts ACC will turn ON and the parking
lights will flash every 2 sec.
ENGINE CRANKS BUT WILL NOT START:
1
.
Check Ignition switch wiring.
See Sec. 1
.
7
“Installing Connector C1
.
Some vehicles require 2 separate
ignition wires I
GN
1
and
I
GN
2 for the vehicle’s ignition system to function properly.
If the vehicle requires
both IGN 1 & IGN
2 then follow the instructions in
Sec 1.7 (C3, Pin 4)
and Ta
ble 1
“Function Option
Chart” Option
4
.
2
.
If the vehicle has a security key, check that the security by
-
pass module is installed properly. See connector
C
3, Pin 12 (White/Red) (GWR)
wire installation instructions
.
ENGINE S
TARTS IN DRIVE OR REVERSE GEAR:
Check t
he location of
C1:
ORANGE (
Starter
output)
wire.
It
MUST be connected to the vehicles start
er
wire close to
the ignition switch, making certain that the Park/Neutral lockout is not bypassed.
AN ACCESSORY (RADIO, HEATER FAN, ETC.) DOES NOT TURN OFF DURING
ENGINE CRANKING AND/OR
TURN BACK ON AFTER CRANKING:
a
.)
Check the connections of C1: wire harness for the correct connection points. See
Figure 1
.
There are
usually only two positions on the ignition switch which disconnect power to the accessories during en
gine
cranking.
ACC and/or IGN 2. In some vehicles IGN 2 is used for either accessories like the heater fan, or is
some times used as an additional ignition system wire
and may be required for starting (see
Table 1
“Function Option Chart”
Option
4
)
.
Check t
he specific wiring diagrams for your Make, Model, and Year
vehicle.
Many of these
can be found at
www.gallotech.com/support.php
.
b
.)
Check
all fuses conn
ected to the Control Module wire harnesses.
If
any are
blown then there must be a short
in the system. Check all wiring thoroughly.
DOORS LOCK/UNLOCK WHEN THEY SHOULD UNLOCK/LOCK:
Connector C
3
Pin 13 and Pin 9
wires have been incorrectly connected to the v
ehicles Master Lock switch.
Revers
ing
the
Lock and unlock wires
Pin 13 & Pin 9
at the C3 connector of the Control Module
should
correct the
problem.
1.
9
TROUBLESHOOTING
INSTALLATION NOTES