Gallo Tech GTS-3RS - Key FOB & Program Function Setup

© Copyright
Gallo Technologies
. All Right Reserved
-
8
-
0
615
1
5
V54RS
9
.
Auxiliary
Output (Door
unlock
Option)
:
Unlock Doors
(default)
When the Auxiliary output is activated the central doors will also unlock.
Do Not Unlock Doors
(
optional
)
When the Auxiliary output is activate
d the central doors will not unlock.
NOTE:
The
Auxiliary Output is
a low current output (125ma max.). A relay must be used to activate devices such as
door poppers, trunk release or window close modules
10
.
Electrical Siren/ Horn:
Electrical Siren
(defa
ult)
:
Set if the 6 tone siren (included) is used.
Horn:
Set if the vehicle’s horn is to be used instead of the 6 tone siren. An additional relay may be required. The
control module siren output is a low current output
(125ma max.)
and must go through a re
lay to operate a vehicle’s
horn.
11
.
Central Locking Time:
When pressing
or
the electrical pulse sent to the door locking/unlocking
mechanism can be set at either 0.
8
seconds or 4 seconds. Mo
st cars will function properly when this option is set to
the factory default of 0.
8
seconds.
(Default):
0
.8 sec pulse
(
Option
):
4 second
pulse
1
2
. Door Unlock Pulses:
Some vehicles require
1 unlock pulse to unlock the driver’s door only and a second pul
se
to
unlock all doors. Most vehicles only require 1
unlock pulse (Default setting)
to unlock all doors.
1 Pulse
(Default):
1 unlock pulse.
Set to unlock drivers door only in 2 pulse vehicles then press
again
to unlock
all d
oors. Also
use
for vehicles requiring only 1 pulse to unlock all doors.
2
Pulses (
option):
2 unlock pulses
.
Set to unlock all doors in vehicles requiring 2 pulses.
Central Locking Time
#
11
must be set to default (0.8 sec) for 2 pulse operation.
13.
Volt
age/Tach Engine running detection
Voltage (alternator) detection (default):
When starting the engine with Remote Start, The system will wait for a
few seconds to determine if the voltage has risen as a result of the engine running.
Tach Signal detection (
optional)
When starting the engine with Remote Start, The system will wait for a few
seconds to determine if
a Tach signal has been detected as
a result of the engine running.
See Sec 1.4 for details.
1
4
. Return Factory Default
: Res
ets
all
Function Option
s to factory default settings.
A.
Code learning (for
replacement
transmitter
s
only
)
Transmitter (Key FOB) Code learning:
The Key FOBs
have been matched to the control module at the factory. If
replacement
key FOBs are used they must first
be learned
to
the
Control M
odule before they will function.
1
.
System must be in Disarm mode (green
“Start/Stop Engine” button
LED flashing).
Both key FOBs should be in
the vehicle.
2
.
Press the valet switch 3
times;
on the 3
rd
press
hold the valet switch for over 5 secon
ds, it will enter the code
learning mode. The green
“Start/Stop Engine” button
LED will
light solid green,
and the parking lights will flash 2
times.
3
.
Immediately (within 5 seconds) press the
button on the
first
key F
OB. The
parking lights
will
flash 4 times
.
Then press the
button on the second FOB
within 5 sec
. The
parking lights
will
again
flash 4 times
.
C
ode
learning
is now complete.
1.
6
Key FOB &
PROGRAM FUNCTION SET UP