Garmin Apollo SL30 COMM

To Next Page

To Previous Page

Installation

Apollo SL30 Installation Manual

Figure 4 - Mounting Frame Assembly

Figure 5 - Cable Routing

Main Page

Installation Manual1
Table of Contents5
Section 1 - Introduction9
About this Manual9
Apollo Sl30 Description9
Eatures10
- General Features10
- Navigation Radio Features10
- Anel10
- Comm Radio Features11
- Physical Specifications11
- Nav Radio Performance Specifications11
- Comm Radio Performance Specifications11
System Interfaces12
- Navigation Receiver12
- Comm Transceiver12
- Serial12
- Erial Nterface12
Regulatory Compliance12
Npacking the Quipment13
Package Contents13
Ther Required Aterials14
Special Tools Required14
License Requirements15
Section 2 - Installation17
Pre -Installation Information17
Installation Overview17
Installation Considerations17
- Mounting Considerations17
- Minimum System Configuration17
- Mounting18
- Mounting Tube Installation18
Pacing19
- Unit Insertion20
- Unit Removal20
Electrical Connections22
- Power22
- Avionics Outputs22
- Serial Interface22
- Speaker and Headphone Outputs22
- Microphone Inputs23
- Transmit Key Input23
- Intercom Selector Switch23
- Remote Flip /Flop Input23
Antenna Installation and Connections23
- Comm and Nav Antennas23
- Use of Splitter and Combiner24
Equipment Interface25
Md200-306/30730
- Onnections31
- Ont Md200-306/30732
Iring34
Iring35
- Sing a37
- C Onnections37
- Pn-101 W Iring39
- Iring40
Nsd 360A40
Iring41
- Final System Check45
- F Eatures46
Limitations on Using a Composite Signal41
Imitations on Distance Speed and Time Nformation41
Post41
- Installation41
- Mounting / Wiring Check41
- Setup and Checkout41
Instructions for Continued Airworthiness48
Section 3 - Specifications49
Electrical49
Physical49
Nvironmental49
Avionics Outputs50
Nav Receiver Performance51
- Vor51
- Localizer51
- Glideslope52
- Obs Resolver52
- Composite Output52
Comm Receiver Performance53
Comm Transmitter Performance53
Intercom Performance54
Control Inputs54
Antenna Requirements54
- Comm Antenna54
- Nav Antenna54
Serial Interface55
Rear Connector Pinout55
Rate.57
Section 4 - Limitations57
Installation57
Computation Rates57
Operational57
Appendix A - Troubleshooting59
Contacting the Factory for Assistance60
Appendix B - Periodic Maintenance61
Vor Checks61
Equipment Calibration61
- Reference Oscillator (Comm Only )61
Cleaning the Front Panel61
Appendix C - Environmental Qualifications63
Appendix D - Accessories65
Appendixd - Accessories65
From Garmin At, Inc65
Appendix E - Serial Interface Specifications67
Input Commands67
Output Messages67
Data Format68
Default Message Output68
Message Formats68
Message Definitions69
- Input Messages69
- Emote vor List70
- Remote Localizer List72
- Request Data Output74
- Set Active Vor/Loc Frequency and Receiver Function75
- Set Standby Vor/Loc Frequency and Receiver Function75
- Requency and75
- Set Standby Comm Frequency and Transceiver Function76
- T Ransceiver F Unction76
- Set Omni -Bearing Select (Obs) Value77
- Dme Sensor Input78
Output Messages78
- Reset Status78
- CDI, Gsi, and Related Flags79
- Decoded Obs Setting80
- Radial from Active vor80
- Radial from Standby vor80
- Panel.80
- Decoded Station Identifier81
- Communications Error81
- Nav Receiver Status82
- Nav Audio Mode82
- Nav Microcontroller Software Version83
- Nav Dsp Software Version83
- Adc Data Output83
- Comm Transceiver Status84
- Comm Software Version84

Garmin Apollo SL30 COMM - Page 21

Table of Contents

Related product manuals