Gastroback Design Espresso Advanced Pro GS

Questions and Answers:

J
Jennifer UnderwoodAug 17, 2025
What to do if espresso does not run through my Gastroback Design Espresso Advanced Pro GS?
- T
  Thomas HornAug 17, 2025
  If espresso isn't running through, check the following: * Ensure the machine is plugged in and the POWER button is on. * The water tank should be filled. * The espresso grind might be too fine. Use a suitable espresso grind. * There might be too much ground espresso in the filter. * The espresso grind might be tamped too firmly. * The filter could be blocked; clean the filters.
D
daviscynthiaAug 20, 2025
What to do if espresso runs out around the edge of the filter holder on my Gastroback Design Espresso Advanced Pro GS Coffee Maker?
- C
  cynthiaguerreroAug 20, 2025
  If espresso runs out around the edge of the filter holder, consider these possible causes: * The filter holder might not be inserted properly; make sure it is correctly inserted in the group head. * There may be espresso grounds around the filter rim; clean any excess grounds to ensure a proper fit. * There might be too much ground espresso in the filter. * The espresso might have been tamped too firmly. * You might be using the incorrect filter for the amount of ground coffee; use the small filter for 1 cup and the larger filter for 2 cups.
B
Bradley CareyAug 22, 2025
Why is there no crema in my espresso from Gastroback Design Espresso Advanced Pro GS?
- V
  Veronica WiseAug 22, 2025
  If there's no crema, it could be due to several reasons: * The espresso might not be tamped firmly enough. * The espresso grind might be too coarse; ensure you use a suitable espresso grind. * The ground espresso might not be fresh; use fresh roasted or pre-ground espresso (ground espresso should not be kept for longer than a week). * The filter holes could be blocked; use the fine pin on the cleaning tool to clear the holes.
P
Pamela GuzmanAug 25, 2025
Why does espresso run out too quickly from my Gastroback Design Espresso Advanced Pro GS?
- J
  Jeffrey WhiteAug 26, 2025
  If espresso runs out too quickly, it could be because: * The espresso grind is too coarse. Ensure you use a suitable espresso grind. * There's not enough ground espresso in the filter. * The ground espresso wasn't tamped firmly enough.
M
molinasethAug 28, 2025
Why is espresso extracting as drops from the portafilter of my Gastroback Coffee Maker?
- C
  Charles AllenAug 28, 2025
  If espresso extracts as drops, it could be due to: * The water tank being empty or low. * The espresso grind being too fine. Ensure you use a suitable espresso grind. * The machine being blocked by mineral deposits. Decalcify the machine.
A
Anthony EnglishAug 30, 2025
Why is milk not foamy after texturing with my Gastroback Design Espresso Advanced Pro GS Coffee Maker?
- K
  Kayla MendozaAug 30, 2025
  If milk isn't foamy after texturing, it could be due to not enough steam (the steam wand may be blocked) or the milk not being fresh and cold. Use cold fresh milk.
K
Kerry RojasSep 2, 2025
Why is my Gastroback Design Espresso Advanced Pro GS making pulsing/pumping sound while extracting espresso or steaming milk?
- M
  Michael LynchSep 2, 2025
  The pulsing/pumping sound is the normal operation of the 17 bar pump. No action is required.
K
Kristen KingSep 5, 2025
What to do if the steam and hot water lights are flashing on my Gastroback Coffee Maker?
- T
  Tonya WaltersSep 5, 2025
  If the steam and hot water lights are flashing, the Steam dial is not in the STAND BY position. Turn the Steam dial to the STAND BY position, and the machine will commence its normal heat up procedure.
N
nicole79Sep 7, 2025
Why is there no ground espresso coming from grinder of my Gastroback Design Espresso Advanced Pro GS?
- A
  Anthony FisherSep 8, 2025
  If no ground espresso is coming from the grinder, check if there are espresso beans in the hopper. If the hopper is empty, fill it.
N
Nathan ZunigaSep 12, 2025
Why grinder does not start when micro switch is pressed on my Gastroback Design Espresso Advanced Pro GS Coffee Maker?
- R
  ronaldmartinSep 12, 2025
  The grinder may not start if the Bean Hopper safety interlock is open (the hopper is not correctly in place). Remove the hopper, check for any debris, and replace the hopper into the correct location.