GE Security FireShield FS1004 - Page 64

Index
Z.2 FireShield Technical Reference Manual
LEDs • 2.2
specifications • 2.2
wiring • 2.3
FSRZI-A
description • 2.3
installation instructions • 2.4
jumper setup • 2.4
lamp test • 1.6
LEDs • 2.3
specifications • 2.3
wiring • 2.4
G
ground and open tests • 4.1
ground fault LED • 1.2
I
IDC
alarm LED • 1.2
disable • 1.5
disable button • 1.2
programming class A or class B • 3.5
programming zone types • 3.4
re-enabling • 1.5
supervisory/monitor LED • 1.2
IDC disabled event • 3.15
IDC trouble LED • 1.2
initiating device circuit • See IDC
inputs
IDC zone types • 3.4
installation
checklist • 2.1
installing
auxiliary power supply • 2.12
cabinet • 2.1
CTM • 2.11
FSDACT • 2.8
FSRPM • 2.10
FSRRM • 2.5
FSRSI • 2.2
FSRZI-A • 2.3
metal dead front • 2.12
power expander transformer • 2.7
J
jumper
10-zone panel settings • C.5
3-zone panel settings • C.1
5-zone panel settings • C.3
FSRRM • 2.5
FSRSI • 2.2
FSRZI-A • 2.4
program jumper • 1.3, C.1, C.3, C.5
L
lamp test • 1.1
conducting a panel lamp test • 1.6
conducting an FSRSI and FSRZI-A lamp test • 1.6
LEDs
binary number value • 3.1
FSRSI • 2.2
FSRZI-A • 2.3
programming • 3.1
system • 1.2
load defaults
description • 3.3, 3.9
programming • 3.3, 3.9
M
maintenance • 4.1
metal dead front
installing • 2.12
MFC-A
FSRRM • 2.6
monitor
IDC zone type • 3.4
LED • 1.2
N
NAC
disable • 1.5
disable button • 1.2
maximum wire length • A.4
programming class A or class B • 3.6
programming outputs • 3.6
programming silence inhibit timer • 3.4
programming silenceable • 3.6
re-enabling • 1.5
silencing • 1.4
trouble LED • 1.2
voltage drop calculation • A.3
NAC disabled event • 3.15
notification appliance circuit • See NAC
O
open and ground tests • 4.1
operation
operating the panel • 1.4
overview • 1.1
outputs
NAC outputs • 3.6
overview
operation • 1.1
system • 1.1
P
panel
silencing buzzer • 1.4
panel silence button
operating mode • 1.2
programming mode • 3.1
password
changing FSDACT • 3.9
FSDACT • 3.9
power expander transformer • 1.3
description • 2.7
installation instructions • 2.7
specifications • 2.7
wiring • 2.7
power LED • 1.2
program jumper • 1.3, C.1, C.3, C.5
program mode
exiting • 3.2
programming
auto NAC silence timer • 3.3
aux power reset • 3.4
buttons • 3.1
find peripherals • 3.3
FSCU • 3.1
FSDACT • 3.8, 3.9
IDC class • 3.5
IDC zone types • 3.4
installing jumper • 3.2
load defaults • 3.3, 3.9
NAC class • 3.6