What to do if my GE 600-1021-95R says 'AC POWER FAILURE'?
If your GE Security System displays an 'AC POWER FAILURE' message, it indicates that the panel power transformer might be unplugged or there could be a power outage. If the transformer is plugged in, check the circuit breaker or fuse that controls the outlet.
What does 'SENSOR XX LOW BATTERY' mean on my GE 600-1021-95R Security System and how to fix it?
If your GE Security System displays 'SENSOR XX LOW BATTERY', it means that a sensor has a low battery. To resolve this: 1. Disarm the system. 2. Remove the sensor cover. If the battery is an Alkaline AA or AAA, change the battery. If the battery is another type, contact your security dealer for assistance.
What does 'LOW BATT' mean on my GE Security System and what to do?
If your GE Security System displays 'LOW BATT', the emergency backup battery in the control panel is low and needs to be recharged or replaced. If AC power is out, the security system may shut down once the battery is below the operating level.
What to do if my GE Security System displays 'SENSOR TROUBLE'?
If your GE Security System displays 'SENSOR TROUBLE', it indicates that a sensor may have an internal problem, a fire/smoke sensor may not have properly reset after activation, or the sensing chamber may be dirty or partially obstructed. You can try to test the sensor in Test Mode. If that doesn't resolve the issue, contact your security dealer for service.
What does 'SENSOR XX TAMPER' mean on my GE 600-1021-95R Security System and how to fix it?
If your GE Security System displays 'SENSOR XX TAMPER', it means a sensor cover is off or open. To fix this, secure the cover and trip the sensor to clear the tamper condition.
What does 'PHONE FAILURE TROUBLE' mean on my GE 600-1021-95R and how do I resolve it?
If your GE Security System displays 'PHONE FAILURE TROUBLE', it means the system can’t communicate with the central monitoring station. Make sure the panel is connected to the special phone jack installed by your security dealer.
What does 'SENSOR SUPERVISORY' mean on my GE 600-1021-95R and what should I do?
If your GE Security System displays 'SENSOR SUPERVISORY', it indicates a problem with how the sensor is communicating with the panel. First, test the sensor in Test Mode. If testing the sensor does not clear the trouble condition, call your security dealer for service.
Why can’t I arm my GE 600-1021-95R to Level 3—AWAY?
If you can’t arm your GE Security System to Level 3—AWAY, it might be because a delay door is open or was not activated after the arming attempt. Close the delay door, arm the system to Level 3, then exit through a delay door.
Why does my GE Security System alphanumeric touchpad display “INVALID” when bypassing a sensor?
If your GE Security System alphanumeric touchpad displays “INVALID” and your fixed display touchpad sounds a single, long beep when you attempt to bypass a sensor, it could be due to several reasons: * The sensor you’re trying to bypass may not be active in the current arming level. For example, an interior motion detector will not be active in Level 2—STAY. * You may be trying to bypass a 24-hour sensor that cannot be bypassed, such as a smoke detector. * Your access code has not been assigned the direct bypassing attribute.
Why don't my lights come on automatically as programmed on my GE 600-1021-95R Security System?
If the lights don’t come on automatically as programmed with your GE Security System, check the following: * Does the lamp have a working bulb? * Is the lamp plugged in at a working outlet that is not controlled by a light switch? * Is the lamp plugged in to a lamp module? * Make sure that you’ve attached the correct time schedule. * Check to see that you’ve set up the time schedule correctly. * Check the User Sheets to see in which partition the light is set up to be active.
General| Model Number | 600-1021-95R |
|---|---|
| Brand | GE |
| Category | Security System |
| Product Type | Door/Window Sensor |
| Power Source | Battery |
| Battery Type | CR2032 |
| Operating Frequency | 319.5 MHz |
| Type | Door/Window Sensor |
| Compatibility | Compatible with GE Security Systems |
| Operating Temperature | 0°C to 49°C (32°F to 120°F) |
To Next Page
