GE 60-806-95R - User Manual

Questions and Answers

G
George GarciaAug 14, 2025
What to do if my GE 60-806-95R displays 'LOW BATT'?
- R
  russelldebraAug 15, 2025
  If your GE Security System shows 'LOW BATT', it means the emergency backup battery's power is low and needs recharging or replacement. If AC power is out, the security system might shut down once the battery goes below the operating level. When AC power returns, the panel will recharge the battery. If the trouble persists for more than 24 hours after AC power is restored, contact your security dealer for assistance.
A
anna53Aug 18, 2025
What to do if my GE Security System says 'SENSOR XX LOW BATTERY'?
- J
  Jacob WilkinsonAug 18, 2025
  If your GE Security System displays 'SENSOR XX LOW BATTERY', it indicates that a sensor has a low battery. Here’s what to do: 1. Disarm the system. 2. Remove the sensor cover. * If the battery is an Alkaline AAA or AA, replace the battery(s). * If the battery is any other type, call your security dealer for service.
J
Jessica DavisAug 21, 2025
What to do if my GE 60-806-95R says 'AC POWER FAILURE'?
- H
  Howard GrahamAug 21, 2025
  If your GE Security System displays 'AC POWER FAILURE', it means the panel power transformer might be unplugged or there's an AC power outage. First, check if the transformer is properly plugged in. If it is, inspect the circuit breaker or fuse that controls the outlet. The backup battery should activate, but if AC power isn't restored within 15 minutes, the system will alert you and the central monitoring station, if your system is monitored. You'll also get another report when the power comes back on.
S
Sharon SellersAug 25, 2025
What does 'PHONE FAILURE TROUBLE' mean on my GE 60-806-95R, and how do I fix it?
- L
  logan74Aug 26, 2025
  If your GE Security System is experiencing PHONE FAILURE TROUBLE, it means the system can’t communicate with the central monitoring station. To resolve this: 1. Ensure the panel is connected to the special phone jack installed by your security dealer. 2. Disconnect the panel from the special phone jack and check your phones for a dial tone. If you hear a dial tone, contact your security dealer for service. If there's no dial tone, it could be a problem with the telephone service in your area. Note that Phone Failure Trouble takes precedence, so clear the message by disarming the panel to see other system messages.
D
danielflemingAug 27, 2025
How to troubleshoot when I can’t arm my GE 60-806-95R Security System?
- C
  carriegriffinAug 28, 2025
  If you're unable to arm your GE Security System, try the following: * If arming to Level 2—STAY or Level 3—AWAY, ensure all monitored perimeter doors and windows are closed. * Press the designated key for a system status to identify the problem. * If issues persist, contact your security dealer.
K
Kelly LucasAug 31, 2025
What does it mean when my GE 60-806-95R Security System says 'SENSOR XX TAMPER'?
- L
  Lynn MeltonAug 31, 2025
  If your GE Security System displays 'SENSOR XX TAMPER', it means a sensor cover is off or open. Make sure the cover is securely in place, and then trip the sensor to clear the tamper condition.
B
benjamin91Sep 3, 2025
What does 'SENSOR TROUBLE' mean on my GE 60-806-95R Security System?
- P
  petersawyerSep 4, 2025
  If your GE Security System displays 'SENSOR TROUBLE', a sensor might have an internal problem, a fire/smoke sensor may not have properly reset after activation, or the sensing chamber could be dirty or partially obstructed. First, test the sensor as described in “Sensor Test.” If testing the sensor doesn't clear the trouble, contact your security dealer for service.
M
Michelle BaileySep 7, 2025
What does 'SENSOR SUPERVISORY' mean on my GE 60-806-95R?
- A
  Amanda CobbSep 7, 2025
  If your GE Security System displays 'SENSOR SUPERVISORY', it indicates a problem with how the sensor is communicating with the panel. First, test the sensor as described in “Sensor Test.” If the sensor doesn’t test OK, contact your security dealer for service.
D
Daisy JohnsonSep 10, 2025
Why can't I bypass a sensor on my GE 60-806-95R Security System?
- B
  Bradley HarrisSep 10, 2025
  If your alphanumeric touchpad displays “INVALID” and your fixed display touchpad sounds a single, long beep when trying to bypass a sensor on your GE Security System, it could be due to several reasons: * The sensor you’re trying to bypass may not be active in the current arming level (e.g., an interior motion detector in Level 2—STAY). * Some sensors can only be bypassed in certain levels (e.g., motion sensors in Level 3—AWAY). * You may be trying to bypass a 24-hour sensor that cannot be bypassed, such as a smoke detector.