3-216 UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS) CHAPTER 3: IEC 61850 COMMUNICATION
3
InjAmp MV Injected current.
SH INJECTION AMPS in amperes.
SubHaPHIZ
InjVol MV Injected voltage.
INJECTED VOLTAGE in volts.
SH INJECTION VOLTS in volts.
FldGnd0PHIZ, SubHaPHIZ
InService SPS LED indication - Relay In-service. The LED IN SERVICE operand. LEDsIHMI
IntermSt1 SPS Intermediate-status detected.
The BREAKER/SWITCH INTERM operand.
BkrΘXCBR, DiscΘXSWI,
GGIO3
IntrAlm SPS Indicates that the current exceeded the maximum interrupting current rating
during the last interruption event.
The BKR ARC 1 MAX OP operand.
CBArc0SCBR
IntrAlmDpo SPS Inverse of IntrAlm.
The BKR ARC 1 MAX DPO operand.
CBArc0SCBR
IrigbFail SPS A bad IRIG-B input signal has been detected.
The IRIG-B FAILURE operand.
LPHD
IsoBlk ACT B90 - Indicates that the isolator position is invalid B_IsoSSWI
IsOn SPS Indicates the time of day timer is on.
The TIME OF DAY 1 ON operand.
TmDayGAPC
IsoPos ACT B90 - Indicates position of isolator. When "On", the related current is included in
differential zone; when "Off", the current is excluded from differential calculations.
B_IsoSSWI
LastClrTm INS Represents the UTC time of user fault reports last cleared time in seconds elapsed
since 1970/01/01, 00.00.00.
The LAST CLEARED DATE actual value.
UFlt0RFLO
LastRptTm INS Represents the UTC time of last user fault report generated time in seconds
elapsed since 1970/01/01, 00.00.00.
The LAST REPORT DATE actual value.
UFlt0RFLO
LastSqNum INS Last sequence number received.
Actual value RxGOOSE1 SqNum.
LGOS
LatchErr SPS A difference is detected between the wanted and actual latch contact state.
The LATCHING OUT ERROR operand.
LPHD
LeoSt SPS Line end open status.
The LINE PICKUP LEO PKP operand.
LinPkpPIOC
LivDea SPS This data object indicates that live/dead conditions have been met.
The SYNC 1 DEAD S OP operand, which indicates that live/dead conditions have
been met.
SynChkRSYN
LivDeaDpo SPS This data object indicates that live/dead conditions have not been met.
The SYNC 1 DEAD S DPO operand, which indicates that live/dead conditions have
not been met.
SynChkRSYN
LivLiv SPS This data object indicates that both sources are live, and that angle, frequency,
and voltage difference and range conditions have been met.
The SYNC 1 SYNC OP operand, which indicates that both sources are live, and that
angle, frequency, and voltage difference and range conditions have been met.
SynChkRSYN
LivLivDpo SPS This data object indicates that one or both sources are not live, or that angle,
frequency, and voltage difference and range conditions have been met.
The SYNC 1 SYNC DPO operand, which indicates that one or both sources are not
live, or that angle, frequency, and voltage difference and range conditions have
been met.
SynChkRSYN
LivV1 SPS This data object indicates that V1 is above the LivVal1 setting.
The SYNC 1 V1 ABOVE MIN operand, which indicates that V1 is above the LivVal1
setting.
SynChkRSYN
LoadDev MV Indicates the motor load standard deviation at the time of the broken rotor bar
data acquisition stage.
LOAD DEV. AT BRB CALC. in x FLA.
BknRotSVBR
LocCmdAcsOff SPS Indicates operations of FlexLogic operand ACCESS LOC CMND OFF SecGSAL
LocCmdAcsOn SPS Indicates operations of FlexLogic operand ACCESS LOC CMND ON SecGSAL
LocMod SPS Capacitor control in local mode.
The CAP 1 IN LOCAL operand.
CapCtlGAPC
Data object
name
CDC Semantics Used in logical nodes…
To Next Page
Loading...
