CHAPTER 3: IEC 61850 COMMUNICATION MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
UR FAMILY – COMMUNICATIONS GUIDE 3-219
3
PhDir1 SPS Indicates Phase Comparison of differential is satisfied per phase, where the last
digit of instance number 1, 2, or 3 refers to phase A, B, and C respectively.
The BUS 1 DIR A/B/C operand.
The STATOR DIFF1 DIR A/B/C operand.
B_DifPDIF, BusDifPDIF,
SttDifPDIF
PhsAInd SPS An LED.
The LED PHASE A operand.
LEDsIHMI
PhsBInd SPS An LED.
The LED PHASE B operand.
LEDsIHMI
PhsCInd SPS An LED.
The LED PHASE C operand.
LEDsIHMI
PlOpn ACT Open pole detector is operated.
The OPEN POLE OP operand.
OpnPlΘSCBR
PosTotVArh MV SRC 1 Total VAr-hour in positive direction EnrMtrMMTR
PosTotWh MV SRC 1 Total Watt-hour in positive direction EnrMtrMMTR
ProcBusFail SPS Process bus system status.
The PROCESS BUS FAILURE operand.
LPHD
ProcBusTrbl SPS Process bus trouble.
The PROCESS BUS TROUBLE operand.
LPHD
ProjectedDif MV Phase angle difference between V1 and projected V2 (V2').
SYNCHROCHECK 1 DELTA PHASE', in degrees which is the phase angle difference
between V1 and projected V2.
SynChkRSYN
ProjectedV1 CMV Projected V2 Voltage phasor.
SYNCHROCHECK 1 V2' voltage phasor, in primary volts.
SynChkRSYN
PtpFail SPS Bad PTP Signal.
The PTP FAILURE operand.
LPHD
Raise SPS PID 1 RAISE operand value PIDRegFPID
RawAnsp MV Raw neutral split phase current. Raw INsp in per unit. NeAUnPTOC
RawAPh WYE Raw Id in per unit for Phase A, B, and C PhAUnPTOC
RecBlk SPS Manually block autoreclose.
The BREAKER 1 BLK RCLS operand.
Bkr0XCBR
RecEna SPS Manually enable autoreclose.
The BREAKER 1 ENA RCLS operand.
Bkr0XCBR
RefWinding INS Reference winding. Number of windings used as the reference winding for ratio
compensation.
PctDifPDIF
RelDpo SPS This data object indicates that not all criteria are fulfilled, and the switching/
operation action is not released to proceed. Complement of Rel.
The SYNC 1 CLS DPO operand, which becomes Off when all synchrocheck criteria
are fulfilled.
SynChkRSYN
RemCmdAcsOff SPS Indicates operations of FlexLogic operand ACCESS REM CMND OFF SecGSAL
RemCmdAcsOn SPS Indicates operations of FlexLogic operand ACCESS REM CMND ON SecGSAL
RemMod SPS Capacitor control in remote mode.
The CAP 1 IN REMOTE operand.
CapCtlGAPC
RemSetAcsOff SPS Indicates operations of FlexLogic operand ACCESS REM SETG OFF SecGSAL
RemSetAcsOn SPS Indicates operations of FlexLogic operand ACCESS REM SETG ON SecGSAL
RemUnA SPS Indicates remote open pole condition is detected in phase A, B, or C.
The OPEN POLE REM OP phase A/B/C operand.
OpnPlΘSCBR
ReSigma SPC Command for the Hi-Z Sigma Value Reset HiZPHIZ
Restart SPS Indicates the motor has restarted.
The MOTOR RESTART operand.
MotThmPTTR
RgDstIP VSG Expected value of Destination IP address field in messages subscribed to by
RxGOOSE#. The multicast IP address of subscribed R-GOOSE message.
LGOS
RgRxMode ENG R-RxGOOSE1 Reception Mode setting: 0 = Unicast, 1 = SSM; 2=ASM LGOS
RgSrcIP VSG Expected value of Source IP address field in messages subscribed to by
RxGOOSE#. The source IP address of subscribed R-GOOSE message.
LGOS
Data object
name
CDC Semantics Used in logical nodes…
To Next Page
Loading...
