GE G60

780 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

7-14 G60 Generator Protection System GE Multilin

7.2 TARGETS 7 COMMANDS AND TARGETS

7

Table of Contents

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software16
- Ur Hardware28
- Using the Relay29
2 Product Description33
- Introduction33
- Specifications47
3 Hardware63
- Description63
- Wiring71
- Direct Input and Output Communications Modules91
- Field and Stator Ground Modules109
4 Human Interfaces131
- Enervista Ur Setup Software Interface131
- Extended Enervista Ur Setup Features134
- Faceplate Interface143
5 Settings157
- Overview161
- Product Setup168
- System Setup253
- Flexlogic296
- Grouped Elements319
- Control Elements415
- Inputs/Outputs452
- Transducer Inputs and Outputs470
- Testing481
6 Actual Values487
- Overview487
  - Actual Values Menu487
- Status487
- Records514
- Product Information516
  - Model Information516
  - Firmware Revisions516
7 Commands and519
- Commands519
8 Theory of Operation533
- Phase Distance through Power Transformers533
  - Description533
  - Example536
9 Application of Settings539
- Setting Example539
- Phase Distance through Power Transformers552
  - Overview552
  - Example553
10 Commissioning555
- Testing555
  - Testing Underfrequency and Overfrequency Elements555
11 Maintenance557
- Modules557
  - Replace a Module557
- Batteries559
  - Replace Battery559
  - Dispose of Battery560
- Uninstall and Clear Files and Data563
- Repairs564
- Storage565
- Disposal566
Parameter Lists567
- Flexanalog Items567
- A.1.1 Flexanalog Items567
- Flexinteger Items594
- A.1.2 Flexinteger Items594
Modbus Communications595
Modbus Rtu Protocol595
- Introduction595
- Physical Layer595
- Data Link Layer595
- B.1.1 Introduction595
- Modbus Rtu Crc-16 Algorithm596
Modbus Function Codes598
- Supported Function Codes598
- Read Actual Values or Settings (Function Code 03/04H598
- Execute Operation (Function Code 05H599
- Store Single Setting (Function Code 06H599
- Store Multiple Settings (Function Code 10H600
- Exception Responses600
File Transfers601
- Obtaining Relay Files Via Modbus601
Memory Mapping603
- Modbus Memory Map603
- Data Formats671
- B.4.2 Data Formats671
Iec 61850709
Overview709
- Introduction709
- Communication Profiles709
- C.1.1 Introduction709
- File Transfer by Iec 61850710
Server Data Organization711
- Overview711
- Ggio1: Digital Status Values711
- Ggio2: Digital Control Values711
- Ggio3: Digital Status and Analog Values from Goose Data711
- Ggio4: Generic Analog Measured Values711
- C.2.1 Overview711
- Mmxu: Analog Measured Values712
- Protection and Other Logical Nodes712
Server Features and Configuration714
- Buffered/Unbuffered Reporting714
- File Transfer714
- Timestamps and Scanning714
- Logical Device Name714
- Location714
- Logical Node Name Prefixes715
- Connection Timing715
- Non-Iec 61850 Data715
- Communication Software Utilities715
Generic Substation Event Services: Gsse and Goose716
- Overview716
- Gsse Configuration716
- Fixed Goose716
- Configurable Goose716
- C.4.1 Overview716
- Ethernet Mac Address for Gsse/Goose719
- Gsse ID and Goose ID Settings719
Iec 61850 Implementation Via Enervista Ur Setup720
- Overview720
- C.5.1 Overview720
- Configuring Iec 61850 Settings721
- About ICD Files722
- Creating an ICD File with Enervista Ur Setup726
- About Scd Files726
- Importing an Scd File with Enervista Ur Setup729
Acsi Conformance731
- Acsi Basic Conformance Statement731
- Acsi Models Conformance Statement731
- Acsi Services Conformance Statement732
Logical Nodes732
- Logical Nodes Table735
- Interoperability Document739
- D.1.1 Interoperability Document739
- Iec 60870-5-104 Point List747
Device Profile Document749
- Dnp V3.00 Device Profile749
- E.1.2 Implementation Table752
Dnp Point Lists756
- Binary Input Points756
- Binary and Control Relay Output757
- Counters758
- E.2.3 Counters758
- Analog Inputs759
- E.2.4 Analog Inputs759
- Radius Server Configuration761
Change Notes763
- Revision History763
- G.1.1 Revision History763
- Changes to the G60 Manual764
Abbreviations768
- Standard Abbreviations768
- G.2.1 Standard Abbreviations768
Warranty770
- Ge Multilin Warranty770
- G.3.1 Ge Multilin Warranty770

Related product manuals

Preview: GE Multilin g60

GE Multilin g60

Preview: GE 869

Preview: GE 339

Preview: GE D60

Preview: GE F60

Preview: GE 850

Preview: GE 889

Preview: GE 350

Preview: GE MI-869

Preview: GE Multilin 850

GE Multilin 850

Preview: GE T35 UR Series

GE T35 UR Series

Preview: GE Multilin 3 Series

GE Multilin 3 Series