To Next PageTo Next PageWhy is there water standing in the bottom of my GE GDT630 Dishwasher?
If there is water standing in the bottom of the tub, the air gap may be clogged, so clean the air gap. Also, check if the high drain loop or air gap is not installed and refer to the Installation Instructions for proper drain line installation.
What to do if my GE GDT630 won't run?
If your dishwasher isn't running, check a few things. First, see if a fuse is blown or the circuit breaker is tripped, and replace the fuse or reset the circuit breaker if needed. Ensure the power is turned on. Also, check if the control panel is locked and unlock it if necessary. If a Critical Fault is present, call for service.
How to turn off beeping at the end of the cycle on my GE GDT630?
To turn off the double beep indicator (or re-activate it if it was previously turned off) on some models of GE dishwashers, press the Heated Dry/Dry Boost pad 7 times within 5 seconds. A triple beep will sound to indicate the end-of-cycle beep option has been turned on or off.
Why does my GE GDT630 beep once every minute?
This is a reminder that your GE dishwasher door has been left open during operation. Press Start and close the door.
What to do if the control panel responded to inputs but dishwasher never filled with water in my GE GDT630 Dishwasher?
If the control panel of your GE dishwasher responds to inputs but the dishwasher never fills with water: * Make sure the door is firmly closed. * Make sure the water valve (usually located under the sink) is turned on. If the problem persists, call for service.
What to do if the start status indicator light is flashing on my GE GDT630 Dishwasher?
If the start status indicator light is flashing on your GE dishwasher, it means the door was opened or the cycle was interrupted. Press the Start pad once and close the door within 4 seconds to start the dishwasher. If you wish to cancel the cycle, press and hold the Start pad for 3 seconds a second time when the dishwasher is running. If the problem persists, call for service.
Why is there water standing in the bottom of the tub of my GE GDT630 Dishwasher?
Water standing in the bottom of the tub of your GE dishwasher is often due to: * A clogged air gap: Clean the air gap. See the Care and Cleaning section. * Improper drain line installation: High drain loop or air gap not installed. Refer to the Installation Instructions for proper drain line installation.
Why won’t my GE Dishwasher run?
If your GE dishwasher won’t run, check the following: * Fuse is blown or circuit breaker is tripped: Replace the fuse or reset the circuit breaker. Remove any other appliances from the circuit. * Power is turned off: Ensure the power to the dishwasher is on, especially if it's controlled by a wall switch. * Control panel is locked: Unlock the control panel. See the Getting started section. * Critical Fault is present: If the Start LED is flashing in a sequence, call for service.
General| Type | Built-In |
|---|---|
| Control Type | Electronic |
| Wash Cycles | 5 |
| Drying System | Heated Dry |
| Noise Level | 50 dBA |
| Color | Stainless Steel |
| Capacity | 16 Place Settings |
| Number of Options | 4 |
| Water Filtration System | Yes |
| Upper Rack Features | Adjustable |
| Dishwasher Interior | Stainless Steel |
| Place Settings | 16 |
| Energy Star Certified | Yes |
| Soil Sensor | Yes |
| Third Rack | No |
| Stainless Steel Tub | Yes |
| Delay Start | Yes |
| Lower Rack Features | Fold-Down Tines |
Ensures correct setup and ongoing maintenance for safe and effective dishwasher operation.
Follows essential safety guidelines for operating the dishwasher to prevent injury or damage.
Resolving problems related to flashing indicator lights and unexpected beeping sounds.
Troubleshooting dirty dishes, spots, filming, and white film on glassware.
Addressing issues with dishes not drying, long cycle times, and control panel response.
Solutions for water standing in the tub or water not pumping out.
Fixing a dishwasher that won't run, control panel lockouts, or critical fault indicators.
