GE GFWS1700 - User Manual

Questions and Answers:

B
Brandy NelsonAug 31, 2025
Why is my GE Washer leaking water?
- T
  Tammy JamesAug 31, 2025
  If your GE washer is leaking water, several factors could be the cause. Check the door gasket to ensure it's properly seated and not torn. If water is present on the back left of the washer, it indicates an oversudsing condition, suggesting you should use less detergent. Inspect the fill and drain hoses to confirm they are tightly connected at both the washer and the faucets, and that the drain hose is correctly inserted and secured to the drain. A clogged household drain could also be the culprit. The dispenser might be clogged, especially if you're using powder soap; remove the drawer and clean both it and the inside of the dispenser box. Make sure that you are using only HE detergent in the correct amount. Finally, if it's a new installation, check the dispenser box for any cracks.
C
Christian NicholsSep 12, 2025
Why are my clothes getting snags, holes, or tears in my GE GFWS1700 Washer?
- P
  Peter WeaverSep 12, 2025
  If you're noticing snags, holes, tears, rips, or excessive wear on your clothes after washing them in your GE Washer, here are a few potential reasons: * The washer may be overloaded. Avoid exceeding the maximum recommended load sizes. * Objects like pens, pencils, nails, or screws might have been left in pockets. Always remove loose items from pockets before washing. * Pins, snaps, hooks, sharp buttons, belt buckles, zippers, and other sharp objects left in pockets can cause damage. Fasten snaps, hooks, buttons, and zippers before washing.
D
Darrell RoweAug 29, 2025
Why does water not enter my GE GFWS1700 or enters slowly?
- K
  Kimberly HollandAug 30, 2025
  If water does not enter your GE Washer or enters slowly, it could be due to several reasons. First, after pressing Start, the washer performs system checks, and water will flow 60 seconds after Start is pressed. Ensure both hot and cold water faucets are fully turned on. Check the water valve screens and inlet hose screen washers for blockages; turn off the water source and remove the hoses to clean the screens. Other potential causes include improper sorting, overloading the washer, or selecting the incorrect wash cycle.
C
cardenaskevinSep 13, 2025
What causes a detergent leak in my GE GFWS1700?
- K
  Kristen PerrySep 13, 2025
  If you notice a detergent leak in your GE Washer, ensure the detergent insert is properly located and fully seated. Also, never put detergent above the max line.
M
Michael SullivanSep 12, 2025
How to get rid of a bad odor inside my GE GFWS1700?
- T
  Timothy GonzalesSep 13, 2025
  If there's a bad odor inside your GE Washer, it could be due to the washer being unused for a long time, not using the recommended quality of HE detergent, or using too much detergent. Try running a Tub Clean cycle to resolve this.
D
Darrell ValdezSep 16, 2025
Why does the control time change or is wrong on my GE GFWS1700 Washer?
- J
  Julie RobinsonSep 17, 2025
  If the control time is wrong or changes on your GE washer, it is normal. During spin, the washer may need to rebalance the load to reduce vibrations. When this happens, the estimated time is increased, causing the time left to increase or jump.
K
kbrownSep 23, 2025
Why does the control time on my GE GFWS1700 display wrong or changes?
- B
  Brandy HartSep 23, 2025
  If the control time on your GE Washer is wrong or changes, it's likely normal. During the spin cycle, the washer may need to rebalance the load to reduce vibrations. When this happens, the estimated time is increased, causing the time left to increase or jump.
M
Matthew CrawfordAug 27, 2025
Why is my GE GFWS1700 not draining, spinning, or tumbling?
- J
  Jermaine OlsonAug 27, 2025
  If your GE Washer isn't draining, spinning, or tumbling, it might be due to several reasons. First, the load might be unbalanced; try redistributing the clothes and running a 'Drain + Spin' or 'Rinse + Spin' cycle. If you're washing a small load with heavy and light items, increase the load size. Also, check if the pump is clogged. Ensure the drain hose isn't kinked or that the washer isn't sitting on it. Your household drain could also be clogged, so it’s worth checking your plumbing. Finally, make sure the drain hose isn't siphoning because it's pushed too far down the drain; ensure there's an air gap between the hose and the drain.
V
victoria36Aug 26, 2025
Why is softener or bleach not dispensing properly in my GE GFWS1700 Washer?
- A
  Anna ParkerAug 26, 2025
  Improper dispensing of softener or bleach in your GE washer may be caused by: * A clogged dispenser: Clean the dispenser drawer monthly to remove buildup of chemicals. * Overfilling: Make sure to use the correct amount of softener or bleach, not exceeding the max line. * Cap issues: Make sure the softener and bleach cap for the dispenser are seated correctly.
M
Margaret FisherAug 25, 2025
Why is there not enough water in my GE GFWS1700?
- H
  hudsonjessicaAug 26, 2025
  If there's not enough water in your GE washer, it is normal. Horizontal washers do not require the tub to fill with water like top-load washers.

GE GFWS1700 Specifications

General

Brand	GE
Model	GFWS1700
Appliance Category	Washer
Type	Front Load
Capacity	4.5 cu. ft.
Color	White
Energy Star Certified	Yes
Number of Wash Cycles	12
Control Type	Electronic
Steam Function	Yes
Sanitize Cycle	Yes
Width	27 inches