Why are clothes too wet after washing in my GE GTW485?
If your clothes are too wet after washing in your GE Washer, ensure that the selected cycle matches the load type. Some fabrics may feel wetter when rinsed with cold water. If the wash load is out of balance, redistribute the load and run it through a Drain & Spin cycle.
What to do if the water won’t drain from my GE GTW485 Washer?
If the water won’t drain from your GE Washer, check that the drain hose is not kinked or that the washer is not sitting on it. Ensure the top of the drain outlet is less than 8 ft (2.44 m) above the floor.
Why is my GE GTW485 leaking water?
Several factors can cause water leaks in your GE Washer. You might be using too much detergent, or the wrong type. Try using less detergent, especially if you have soft water. Ensure your fill and drain hoses are properly connected and tightened at the faucets, with rubber washers installed. Also, check your household plumbing for clogs, and make sure the drain hose isn't rubbing against the wall. Finally, ensure constant water pressure doesn't stress the fill hoses, and consider replacing them every 5 years.
What to do if my GE GTW485 won’t operate?
If your GE Washer won't operate, there are several potential causes: * Ensure the washer is securely plugged into a working outlet. * Check that both hot and cold water faucets are fully turned on. * Make sure the lid is closed and press Start, as a safety feature prevents operation with the lid open. * Inspect your house circuit breakers or fuses and replace if necessary; the washer should have a separate outlet. * Try resetting the electronics by unplugging the washer, waiting two minutes, plugging it back in, and pressing Start. * Confirm that you have pressed the Start button.
What to do if my GE GTW485 won’t drain?
If your GE Washer isn’t draining, make sure the drain hose isn't kinked or that the washer isn't sitting on it. The top of the drain outlet should be less than 8 ft (2.44 m) above the floor. Straighten the drain hose and ensure proper connection.
Why are my clothes too wet after washing in my GE GTW485?
If clothes are coming out of your GE Washer too wet, ensure that the cycle selected matches the load you are washing. Some fabrics will feel wetter when rinsed with cold water. If the wash load is out of balance, redistribute the load in the washer and run it through a Drain & Spin cycle.
Why does the agitator seem loose on my GE GTW485 Washer?
If the agitator seems loose on your GE Washer (on some models), it is designed to be flexible to allow for care of large bulky items such as comforters; this is normal.
How to fix a GE GTW485 that won't operate?
If your GE Washer isn't operating, here are a few things to check: * Make sure the power cord is securely plugged into a working outlet. * Ensure both hot and cold water faucets are fully turned on. * Confirm that the lid is closed and press Start, as a safety feature prevents operation when the lid is open. * Check your house's circuit breakers or fuses and replace if necessary. The washer should ideally have its own separate outlet. * Try resetting the electronics by unplugging the washer, waiting two minutes, plugging it back in, and then pressing Start. * Ensure you have pressed the Start button.
How to fix a GE GTW485 Washer when the water won’t drain?
If the water isn't draining from your GE washer, check if the drain hose is kinked or improperly connected. Straighten the drain hose, ensure the washer isn't sitting on it, and verify that the top of the drain outlet is less than 8 ft (2.44 m) above the floor.
How to reduce suds in my GE Washer?
To reduce excessive suds in your GE Washer, consider the following: If you have soft water, use less detergent. Measure your detergent carefully, and if the load is lightly soiled, reduce the amount of soap. Also, consider switching to a High Efficiency detergent.
Read all instructions before using the appliance and follow basic precautions.
Overview of initial setup, operation, and the washing machine's control panel.
Matching laundry items to the best wash cycle for optimal performance.
Specifications for water supply, pressure, temperature, and drain hose connection.
Steps for connecting hoses, power, and ensuring proper grounding.
Guides to diagnosing and resolving common issues before contacting service.
Details of the warranty coverage, duration, and terms for GE Appliances washers.
General| Brand | GE |
|---|---|
| Model | GTW485 |
| Appliance Category | Washer |
| Washer Type | Top Load |
| Capacity | 4.5 cu. ft. |
| Color | White |
| Number of Wash Cycles | 11 |
| Control Type | Electronic |
| Spin Speed | 700 RPM |
| Energy Star Certified | Yes |
| Width | 27 in |
| Depth | 27 inches |
| Height | 44 in |
| Agitator Type | Dual Action Agitator |
To Next Page
